Focal

This acoustic insulation kit is completing and essential to a quality car audio installation. From its use depends optimum acoustic rendering of speakers, amplifiers and installed accessories. Technical materials made of honeycombed damping material, an Aluminum sheet and a viscoelastic complex (Butyl).Features:Soundproof your carAttenuates the speaker back waveReplaces Plain chantObserve carefully the laying conditions (min. temperature +15° on a clean surface)Content: one 0.5 x 6m sheet (3m2)Money-saving extra sizeCapacity: about 4 doorsIncreases the bass level in your carIncreases the soundproofing of outside noise

This ‘ready-for-use’ wiring kit includes the best in terms of high-end connectivity: 17ft (5.20m) x 35mm2 (3087 strand) 100% OFC power cable, 2ft 3in (0.70m) ground cable, gold-plated fuse holder with a 200A fuse + equipped with a digital battery reader, an ER5 RCA cable, and a set of accessories. This kit is ideal for a 1500W amplifier. Focal recommends connecting this kit to the FPS 3000 or to a system with an amplifier and a subwoofer wired in series.

The AP-4340 4-channel class AB amplifier can be used in three modes: 4, 3 or 2-channel. In 4-channel mode, its CEA power of 4 x 70W RMS will allow you to get the most from your Auditor kits installed up front and in the rear. The 3-channel mode enables you connect a kit to channels one and two, as well as an Auditor subwoofer to channels three and four in bridged mode for a CEA power of 190W RMS under 2 Ohms. The 2-channel mode, which consists of bridging channels 1-2 and 3-4, provides a CEA power of 2 x 190W RMS under 2 Ohms. Equipped with high-pass and low-pass crossovers, as well as a subsonic crossover, the AP-4340 amplifier guarantees the optimal performance of the kits and subwoofers in this line. Specifications:4/3/2-channel A/B class amplifierRCA inputsCEA Power (4Ω): 4x70W RMSNom. power (2Ω): 4x95W RMSNom. power (bridged 4Ω): 2x190W RMSHigh-pass crossover (channel 1-2):60Hz – 1.2KHzHigh-pass crossover (channel 3-4):100Hz – 2.2KHzLow pass crossover: 50 - 250HzFull range modeBandwidth: 10Hz - 30KHzDimensions (LxHxl) :1325/64"x2"x91/4" (340x50x235mm)​

The Access 165 AS car audio 2-way component kit is of sufficiently high sensitivity to be directly connected to a car stereo. It has 3-position tweeter adjustment for optimal listening comfort. Accessories shipped with the tweeter enable multiple fitting options and finding the best sound stage.Discover new musical sensations and enter the world of performance with a kit that offers multiple configuration possibilities to enhance your audio installation. This range's reference model is a best-seller with a worldwide reputation..Features:Cone DFS® (Dual fiberglass Structure)(climatic and power) high resistanceHigh sensitivity (Direct headunit using)Tweeter level adjustment Extented in low frequenciesSpecifications:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 07/16" (11mm)Magnet: 31/3" (85mm)Tweeter: Aluminum inverted domeAjustable Tweeter level: 3 positions (-3/0/+3dB)Crossover: 12dB/octMax. power: 120 WattsNom. power: 60 Watts RMSSensitivity (2.83V/1m): 91.3dBFrequency response: 60Hz – 20kHzAccessories: Supplied grilles  

The 5'' (130mm)  Access 130 AS 2-way component speaker kit is very versatile. It fits perfectly into your vehicle interior and offers three different mounting options for the tweeter. You can very easily use the tweeter's 3-position level control, thanks to its separate, easy-to-fit filter.This kit combines dynamic bass with precise treble, for prolonged listening without auditory fatigue. Focal pays extreme attention to the reliability and musicality of all its products including the Access range, which has all the brand's DNA and tradition of more than 30 years..Features:Cone DFS® (Dual fiberglass Structure) (climatic and power) high resistance Tweeter level adjustmentSpecifications:Woofer: 5" (130mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 07/16" (11mm)Magnet: 31/3" (85mm)Tweeter: Aluminum inverted domeAjustable Tweeter level: 3 positions (-3/0/+3dB)Crossover: 12dB/octMax. power: 100 WattsNom. power: 50 Watts RMSSensitivity (2.83V/1m): 90dBFrequency response: 65Hz – 20kHzAccessories: Supplied grilles  

Universal ISS 130  2-way component kit.Features:High sensitivityShallow mounting depth (49 mm)Partial horn loading tweeterDynamics and neutrality2 tweeter support typesSpecifications:Woofer: 5" (130mm)Voice-coil diameter: 1" (25.5mm)Voice-coil height: 01/3 (8.4mm)Magnet: 213/16 (72mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/oct (tweeter)Max. power: 120WNom. power: 60W rmsSensitivity (2,83 V/1 m): 91.9dBFrequency response: 75Hz – 20kHzAccessories: Supplied without grille 

The Performance line’s P 30 DB subwoofer has a nominal power of 300W RMS. It is ideal for using with sealed or bass-reflex enclosures. Its 2 x 4 Ohm double voice coil gives you various options for hooking it up to an amplifier.The Sub P30 DB really gives your car audio system an upper edge. It offers high power handling thanks to the 2″ (50mm) voice coil with a Kapton frame.. The butyl suspension gives the subwoofer more durability, and the decompression of the spider ventilates the voice coil. This enables your system to achieve extreme performance with pronounced and tight bass.Features:For sealed or vented boxHigh sensitivity2 x 4 Ohms dual voice coil511/16" (14,5cm) dual ferriteSpecifications:Diameter: 12” (300mm)Voice-coil diameter: 23/8” (60mm)Voice-coil height: 11/8” (28mm)Magnet: 511/16” (145mm)Frequency response: 27Hz – 500HzImpedance: 2 x 4 OhmsMax. power: 600 WattsNom. power: 300 Watts rmsSensitivity (2.83V/1m): 93.4dB

The 12'' Access 30 A4 subwoofer develops a rated power of 250 W RMS. The essential complement to your car audio installation, it gives your kit heightened dynamics and you benefit from powerful Focal sound. Ideal for use in sealed and bass reflex enclosures, it achieves extreme performance levels and powerful, deep bass.Features:DFS® cone (Dual Fiberglass Structure)Powerful 43/4" (12cm) magnet: 250 Watts RMSSpider decompression ventilated coilGreat dynamicsHigh powerSpecifications:Diameter: 12" (300mm)Voice-coil diameter: 2" (50mm)Voice-coil height: 1" (25mm)Magnet: 43/4" (120mm)Max. power: 500WNom. power: 250W RMSSensitivity (2,83 V/1 m) : 87dBFrequency response: 32Hz – 500HzImpedance: 4 Ohm

Treat your car audio installation to powerful sound thanks to the PC 165, a coaxial speaker driver kit with 61/2″ (16.5cm) woofers. The tweeters can be orientated for even greater listening comfort. The woofer, with its Polyglass cone, will surround you in warm sound without colouration.The speaker driver with integrated crossover makes installation easier. Connect your kit with great ease and enjoy the extreme sensations of listening to Performance speaker drivers. Create your sound with ease.For thirty years, French experts have been innovating to bring you the best technologies to increase listening comfort. Focal soon became the reference in the car audio sector as well as in the high-end market. The Performance line was designed so you can create your ideal system: powerful, precise and high- fidelity.Features:Partial horn loading tweeterHigh sensitivityHigh soundstageDynamics and neutralitySpecification:Diameter: 61/2” (165mm)Voice-coil diameter: 1” (25mm)Voice-coil height: 07/16” (10.5mm)Magnet: 31/8” (80mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/octRotating tweeterMax. power: 120 WattsNom. power: 60 Watts rmsSensitivity (2.83V/1m): 93.6dBFrequency response: 60Hz – 20kHzAccessories: Supplied grilles

IS 690TOY is a two-way component kit with a 6x9’’ woofer and a tweeter enabling to equip factory locations up front and improving the musicality of numerous Toyota® models. Reliable, neutral and powerful, the compactness and the ergonomics of the IS 690TOY makes it easy to integrate thanks to the factory connectors.Features:Easy installationRespect of the original Toyota® connectorsBetter precision in high frequenciesCompact tweeter for better adaptation in factory locationHigh-density rubber ring for acoustic sealing with the door panelSpecification:Woofer : 6x9" (165x230mm)Diamètre bobine : 13/16" (30mm)Moteur : 31/3" (85mm)Aluminum inverted dome compact tweeterMax. power: 150 WattsNominal power: 75 Watts RMSSensitivity (2.83V/1m): 92dBImpedance: 4 OhmsFrequency response: 50Hz - 20kHz

IC 165 VW is a coaxial speaker kit compatible with Volkswagen®  cars. Easy to install, thanks to OEM Volkswagen® connectors, integrated crossover and Volkswagen® standard ABS molded basket, both 6,5'' (16,5cm) speakers are equipped with Fiberglass cones that provide a neutral sound, without coloration. Aluminum inverted dome TN44 tweeter provides non-directive smoothness and definition trebles.Features:Facilité de montageSolution "clé en main" pour upgrader l'installation d'origineRespect de la connectique Volkswagen® d'origineSon de qualité audiophilePlus grande précision dans les hautes fréquencesSpecification:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 07/16" (11.6mm)Magnet: 31/3" (85mm)Aluminium inverted dome TN44 tweeterMax. power: 120 WattsRMS power: 60 WattsSensitivity (2.83V/1m): 92 dBBandwidth: 60 Hz – 20 kHzNominal impedance: 4 Ohms

The PC 130 2-way coaxial kit was designed to provide you with live sound in every aspect. These car audio speaker drivers have an assertive design: with their chrome-plated magnet and their aluminium chassis, they will perfectly integrate your car. PC 130 speaker drivers are extremely resistant over time thanks to the materials used, such as butyl and aluminium.With its inverted dome tweeter and its Polyglass cone woofer, this car audio kit offers mellow and natural sound without directivity. The soundstage is high and realistic thanks to the tweeter’s acoustic horn which also allows you to orientate the tweeter for increased listening comfort.Features:Partial horn loading tweeterHigh sensitivityHigh soundstageDynamics and neutralitySpecification:Diameter: 5” (130mm)Voice-coil diameter: 1” (25mm)Voice-coil height: 07/16” (11mm)Magnet: 31/3” (80mm)Processed Aluminum inverted dome tweeter Integrated crossover: 6dB/octRotating tweeterMax. power: 120 WattsNom. power: 60 Watts rmsSensitivity (2.83V/1m): 91.6dBFrequency response: 80Hz – 20kHzAccessories: Supplied grilles

The IS 165TOY is a two-way component kit with a 6,5" woofer and tweeter that has improved the musicality of countless Toyota's® around Europe and the world. Keeping the factory connectors and equipment in mind for Toyota® vehicles was integral to the development of the IS 165TOY. Excellent reliability, neutral sound, and deep bass are complemented by a compact and simple design..Features:Easy installationRespect of the original TOYOTA® connectorsBetter precision in high frequenciesCompact tweeter for better adaptation in factory locationHigh density rubber ring for acoustic sealing with the door panelSpecifications:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Magnet: 31/3" (85mm)Aluminum inverted dome compact tweeterMax. power: 120 WattsNominal power: 60 Watts RMSSensitivity (2.83V/1m) : 91dBImpedance: 4 OhmsFrequency response: 60Hz - 20kHz   

With its 315/16″ (100mm) speaker drivers, this kit will have no problem finding its place in your vehicle. Its inverted dome tweeters provide mellow sound and great definition without directivity. As to its Polyglass cone woofer, it ensures natural sound without colouration.This coaxial kit will give your vehicle natural and dynamic sound. These speaker drivers with high sensitivity are also very resistant thanks to the butyl suspension as well as the rigid aluminium chassis. Another key point is the tweeter’s acoustic horn which improves the position of the soundstage.With more than 30 years of experience in the field of high-end audio equipment, Focal has become a reference in the car audio sector. Hundreds of technological innovations have marked Focal’s history and development for your greatest listening pleasure.Features:Partial horn loading tweeterHigh sensitivity High soundstageDynamics and neutralitySpecification:Diameter: 4” (100mm)Voice-coil diameter: 1” (25mm)Voice-coil height: 03/8” (9.5mm)Magnet: 213/16” (72mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/octRotating tweeterMax. power: 100 WattsNom. power: 50 Watts rmsSensitivity (2.83V/1m): 90.9dBFrequency response: 100Hz – 20kHzAccessories: Supplied grilles

ISC 570 2 way Coaxial Kit.Features:High sensitivityShallow mounting depth (82.5 mm)Great improvement from original car speakersDynamics and neutralitySoundstage orientationSpecification:Woofer: 5x7 (130x180mm)Voice-coil diameter: 1" (25.5mm)Voice-coil height: 07/16 (11mm)Magnet: 31/3 (85mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/octMax. power: 120WNom. power: 60W rmsSensitivity (2,83 V/1 m) : 94.1dBFrequency response: 65Hz – 20kHzAccessories: Supplied without grille​

ISC 165- 2 way Coaxial Kit.Features:High sensitivityShallow mounting depth (82.5 mm)Great improvement from original car speakersDynamics and neutralitySoundstage orientationSpecification:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 01/4 (7mm)Magnet: 39/16 (90mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6/6dB/octMax. power: 140WNom. power: 70W rmsSensitivity (2,83 V/1 m) : 93.2dBFrequency response: 60Hz – 20kHzAccessories: Supplied without grille​

The Performance line’s P 25 DB subwoofer has a nominal power of 250W RMS. It is ideal for using with sealed or bass-reflex enclosures. Its 2 x 4 Ohm double voice coil gives you various options for hooking it up to an amplifier.The Sub P25 DB really gives your car audio system an upper edge. It offers high power handling thanks to the 2″ (50mm) voice coil with a Kapton frame, and to the 511/16″ (145mm) double ferrite magnet. The butyl suspension gives the subwoofer more durability, and the decompression of the spider ventilates the voice coil. This enables your system to achieve extreme performance with pronounced and tight bass.Features:For sealed or vented boxHigh sensitivity2 x 4 Ohms dual voice coil511/16" (14,5cm) dual ferriteSpecifications:Diameter: 10” (250mm)Voice-coil diameter: 2” (50mm)Voice-coil height: 1” (25mm)Magnet: 511/16” (145mm)Frequency response: 42Hz – 500kHzImpedance: 2 x 4 OhmsMax. power: 500 WattsNom. power: 250 Watts rmsSensitivity (2.83V/1m): 90.9dB

This double voice coil subwoofer benefits from a polypropylene cone with high rigidity, a crucial requirement in the low end for preventing distortion at very high volume.Equipped with double ferrite magnets and 2” (50mm) voice coils, these subwoofers combine high sensitivity and high power handling. The 2 x 4 Ohms double voice coil is the perfect finishing touch to the mechanical design. This allows the subwoofer to be wired in parallel under 2 Ohms in order to get the most from your amplifier.Features:High power handlingPorted or sealed enclosureParralel voice coil wiring possible even more SPLSpecifications:Diameter: 12" (300mm)Voice coil diameter: 2" (50mm)Polypropylene coneMax. power: 600WNom. power: 300W RMSSensitivity (2.83V/1m): 90dBImpedance: 4+4 OhmsFrequency response: 30Hz - 500kHz

The Access 165 AC coaxial kit puts Focal sound in your car with no fuss. Measuring 6½" (165mm) in diameter and with 60 W rated power, this kit is easily fitted for an effective, responsive audio system.This car audio kit marks access to the performance world: remarkable power handling, deep bass and extremely dynamic sound. All this is possible thanks to numerous Focal technical innovations and a new choice of specific materials.Features:Cone DFS® (Dual fiberglass Structure) (climatic and power) high resistanceHigh sensitivity (Direct headunit using)High dynamiqueRotativ tweeterSpecification:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 07/16" (11mm)Magnet: 31/3" (85mm)Tweeter: Aluminum inverted domeCrossover: (4,7Khz) 6dB/octMax. power: 120 WattsNom. power: 60 Watts RMSSensitivity (2.83V/1m): 91dBFrequency response: 60Hz – 20kHzAccessories: Supplied grilles

Universal ISC 130-2-way coaxial kitFeatures:High sensitivityShallow mounting depth (49 mm)Great improvement from original car speakersDynamics and neutralitySoundstage orientationSpecification:Woofer: 5" (130mm)Voice-coil diameter: 1" (25.5mm)Voice-coil height: 01/3 (8.4mm)Magnet: 213/16 (72mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/octMax. power: 100WNom. power: 50W rmsSensitivity (2,83 V/1 m) : 90.3dBFrequency response: 90Hz – 20kHzAccessories: Supplied without grille

Focal ISC 100-2-way coaxial kitFeatures:High sensitivityShallow mounting depth (49 mm)Great improvement from original car speakersDynamics and neutralitySoundstage orientation​Specification:Woofer: 4" (100mm)Voice-coil diameter: 1" (25.5mm)Voice-coil height: 01/3 (8.4mm)Magnet: 213/16 (72mm)Processed Aluminum inverted dome tweeterIntegrated crossover: 6dB/octMax. power: 100WNom. power: 50W rmsSensitivity (2,83 V/1 m) : 90.3dBFrequency response: 90Hz – 20kHzAccessories: Supplied without grille

IC 165 VW is a 2-way component kit compatible with Volkswagen® group’s cars which use this diameter and connector standard.Easy to install, thanks to original Volkswagen® connector, integrated crossover and and Volkswagen® standard ABS molded basket, both 6,5'' (16,5cm) speakers are equipped with Fiberglass cones that provide a neutral sound, without coloration.This kit was developped for a replacement in Volkswagen® group cars using this same standard fixing. Some of cars from Volkswagen® group can be used this same attachment (Seat/Skoda®).Features:Easy installation, 100% plug and play (1h max.)Original installation upgradeRespect of the original VOLKSWAGEN® connectorsAudiophile quality soundBetter precision in high frequenciesAdaptation of the tweeter in the original locationSpecification:Woofer: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 07/16" (11.6mm)Magnet: 31/3" (85mm)Aluminium inverted dome TN44 tweeterCrossover: 0/6dBMax. power: 120 WattsRMS power: 60 WattsSensitivity (2.83V/1m): 92dBBandwidth: 60Hz – 20kHzNominal impedance: 4 Ohms

By guaranteeing installation in less than an hour, keeping the original car radio, the IFVW Golf 6 brings a solution to all the Volkswagen Golf 6 owners who whish to discover the best of the audiophile sound. All the tools are supplied and a video shows the different steps of the installation. It couldn't be easier!*This kit is not compatible with : Volkswagen Golf 6 CC, Golf 6 SW, Golf 7Features:100% plug and playOriginal installation upgradeQuick and easy installation (1h max)Better precision in high frequenciesImprovement of the original acousticsFull pack (tools and staples supplied)Significant results without changing the original system, evolutivity if amplification or replacement of the car stereoSpecifications:Diameter: 6 1/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 0 7/16" (11.6mm)Magnet: 3 1/3" (85mm)Aluminum/magnesium inverted domeTNB tweeterCrossover: 12/18dB/oct (4kHz)Max. power: 150 WRMS power: 75 WSensitivity (2.83V/1m): 92.4dBKit bandwidth: 65Hz – 25kHzNominal impedance: 4Ω

The PS 130 V1 2-way component kit is resolutely high tech: aluminium chassis, chrome-plated magnet, butyl suspension, separable crossovers... This car audio system inspires quality manufacturing, and its strong design guarantees resistance over time.Create your own sound with this high- quality 2-way component kit. The TNP tweeter offers mellow sound and great definition without directivity, the Polyglass cone ensures natural sound without colouration, the woofer’s phase plug improves dispersion, and the separable crossovers make installation easier... Focal provides you with the best technologies to ensure you achieve optimal sound quality.This car audio kit truly makes the difference: the tweeter levels can be adjusted, and you can choose between three cut-off frequencies as well as three different mounting options for the tweeters. Thanks to the highly customisable sound this system offers, you can adapt your kit to your heart’s content..Features:Create your own sound in your car with this two way component kit.Polyglass conePartial horn loading tweeterHigh sensitivityDynamics and neutralityThree tweeter cut-off frequenciesThree tweeter integration possibilitiesSpecifications:Diameter: 5” (130mm)Voice-coil diameter: 1” (25mm)Voice-coil height: 07/16” (11mm)Magnet: 31/3” (85mm)Better dispersionSensitivity (2.83V/1m): 91.4dBFrequency response: 80Hz – 20kHzAccessories: Supplied grillesProcessed Aluminum inverted dome tweeterSeparate crossover: 0; -3; -6dBMax. power: 120 wattsNom. power: 60 watts rms

The E 30 KX is a 12" (30cm) subwoofer with very high power handling. It has an impressive SPL of 86.5dB (2.83 V/1 m) and a sealed box or bass-reflex type enclosure of 28 to 35L! The E 30 KX subwoofer takes full advantage of the acoustic qualities of Kevlar®cones. Light, rigid and with excellent damping, they provide extremely dynamic bass. Their yellow colour is legendary of the K2 Power line’s identity.All the components used for this subwoofer have been optimised to improve performance. The cone is fixed to the frame using a new robust and very reliable rubber suspension, whose exclusive shape has been optimised to provide very high excursion. The aluminium frame has also been redesigned to improve voice coil excursion. All moving parts benefit from this excellent excursion, giving the subwoofer tight, punchy and dynamic bass.The oversized “Dual Magnet” has been given a new voice coil cooling system to improve cooling and also to improve the subwoofer’s performance and power handling. The progressive spider profile is designed to provide a full-bodied bass to increase linearity, precision and dynamic range. Features:Impressive power handlingHigh SPLHigh excursionFor sealed and vented enclosure(1 to 1,3 cu ft (28 to 35l) in sealed for optimized performanceSpecifications:Diameter: 12" (300mm)Voice coil diameter: 29/16" (65mm)Voice coil height: 23/16" (55mm)Motor: MagnetTweeter: Composite K2 Power "W"Sandwich coneMax. power: 1600WNom. power: 800W RMSSensitivity (2,83V/1m): 86.5dBFrequency response: 25Hz - 500HzImpedance: dual 2x4 Ω

The FPX 4.800 is a very compact 4-channel amplifier with a power of 4x120 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.800 is the most versatile model in this range. Thanks to its very high power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair output lines. The high power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line.Features:D class 4/3/2 Channel amplifierStable under 2 OhmsAudio Mos-Fets - Optimized efficiencyHigh performance compact heat dissipation chassisHigh power and current dynamic reserveSpecifications:D Class amplifier - 4/3/2 channelsCEA power (4 ohms): 4x120 WrmsMaximum power (2 ohms): 4x185WrmsMaximum power (bridged 4 ohms): 2x370WrmsBandwidth: 10Hz – 20KHzTotal harmonic distortion: 0.01%SNR (1W/A): >76dBAConfigurable filters High Pass / Low Pass : 50Hz-500HzBass boost: (0/12dB)Mirroring Mode: (4CH/2CH)Protections: Short circuit / low impedance /reversal of polarity / DC / power drop / heat protectionDimensions (LxHxW): 921 (237x132x5

The 165W-RC car audio kit is packed with Focal’s renowned technologies. The 2 Ohm voice coil is only 1/2 inch in diameter (12mm) and 13/8 inches high (35mm) to ensure low distortion and improved sensitivity. The ‘W’ sandwich cone and the beryllium tweeter provide extraordinary rigidity.Specifications:Tweeter: TB 872, Pure Beryllium inverted domeChassis: Coated ZAMAKMax power: 160WNominal power: 80WSensitivity: 93 dBFrequency response: 60 Hz – 30 kHz

Multiferrite magnet 13" (33cm) subwoofer. Its high sensitivity combined with its high acceptable power that guarantees deep and dynamic bass.Specifications:Type : 33cm Subwoofer77mm diameter single voice coilMax. power. : 800WNom. power : 400WSensitivity (2,83V/1m) : 92dBFrequency response : 27 Hz - 350 Hz

5-channel FPX 5.1200 amplifier has a maximum power of 4 x 120 Watt + 1 x 720 Watt at 2 Ohms! The input selector (2/4/6 channels) duplicates channels, meaning there will always be 5 output channels, even if the head unit only has one or two stereo outputs.To perfectly tune the subwoofer to the rest of the installation, the bass channel has a low-pass active crossover, a bass equaliser, phase adjustment and a subsonic filter (particularly useful for cutting off frequencies which are too low for a small subwoofer). The remote control enables you to adjust the bass level from the driving seat depending on the type of music you’re listening to.Stable at 4 and 2 Ohms, this new FPX amplifier will drive most speaker drivers on the market with just the right amount of power: 4 x 75 Watts + 1 x 420 Watts RMS at 4 Ohms (CEA standard). With its power and contained volume, FPX 5.1200 makes the installation easier in order to make the most of your boot space.Specifications:Only one amplifier for the entire hi-fi installationEasier to integrate and installCompact designSubstantial power and great musicalityExtremely versatileA dedicated subwoofer channel (+ remote control)Input selector (2/4/6 channels)Stable under 4 and 2 OhmsAdjustable active crossover for each pair of channelsDimensions: 13.25″ x 6.8″ x 2.25″ (337 x 175 x 57mm)

The FPX 4.400 is a very compact 4-channel amplifier with a power of 4x70 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.400 is the most “sound quality” model in this range. Thanks to its very comfortable power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair output lines. The power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line.Features:An audiophile and versatile amplifierOptimized heat dissipationExtremely versatileRemarkable power/performance/price ratioAB Class 4/3/2 Channels amplifier - Dedicated to sound qualityStable under 2 OhmsAudiophile Sanken® TransistorsHigh performance compact heat dissipation chassisHigh power and current dynamic reserveSpecifications:4-/3-/2-channel Class ABD amplifier2-/4-channel input modesStable at 2 OhmsActive crossover for each pair of channelsThe FPX 4.400 measures 314x175x57mm)CEA power (4 ohms) 4x70 Watts RMS Max. power (2 ohms) 4x100 Watts RMS Max. power (4 ohms bridged) 2x200 Watts RMS Bandwidth (-3dB) 10Hz – 22KHz THD 0.04% Crosstalk (1 KHz) > 54dB SNR (1W/A) > 77dBA

The IBus 2.1 subwoofer has a compact aluminum chassis. It’s ultra-thin, very robust, and it offers great heat dissipation. The chassis features a flat 8" (20cm) subwoofer with a nominal power of 75W RMS.Thanks to the 2 x 55W RMS amplification, combined with an active enclosure, your audio system will benefit from deep and tight bass, as well as from a very powerful 2-way Integration car audio kit.Features:ISO Plug & Play cable provided (direct connection to ISO head unit)Easy installation under car seat (takes up little space)Intensifies the bass of your audio systemPowerful amplification solution (allowing you to keep the ergonomics of your original source without loosing display or control functions)Recreate a high-performance 2.1 system in your carSpecifications:Type: Flat active subwoofer enclosure (20cm/8")+ 2-channel amplifierSubwoofer power: 150W max / 75W RMSSubwoofer frequency response: 45Hz - 150Hz2-channel amplifier power: 2x110W Max / 2x55W RMS2-channel amplifier frequency response: 55Hz - 55KHzImpedance: 4 Ohms (Warning: not stable under 2 OhmsSignal cable: ISO Plug & Play cable: 3m (included)SNR > 80dBA - THD < 0.08 %Height: 71.5mm (2.8") - Length: 344mm (13.5") - Width: 250mm (9.8") 

The 25 K is a very compact 10" (25cm) subwoofer. It offers very high power handling and exceptional reliability. Available in sealed box or bass-reflex type enclosures, this subwoofer has an astonishing SPL of 84.5dB considering its compact design!It features a yellow Kevlar® cone which is light, rigid and has excellent damping to provide extremely dynamic bass. The cone is fixed to the frame using a new robust and very reliable rubber suspension, whose exclusive shape has been optimised to provide very high excursion. The aluminum frame has also been redesigned to improve voice coil excursion. All moving parts benefit from this excellent excursion, giving the subwoofer tight, punchy and dynamic bass.The oversized “Dual Magnet” has been given a new voice coil cooling system to improve cooling and also to improve the subwoofer’s performance and power handling.Features:Compact sizeHigh powerFor sealed and vented enclosure (0.6 to 0.77 cu ft (17 to 22L) in sealed for optimized performanceSpecifications:Nominal power: 600W RMSMaximum power: 1200WSensitivity: (2.83V/1m) 87.5dBCone Kevlar sandwichSurround ButylNom. impedance: 4+4 ΩDC resistance: 3.2+3.2 ΩVC diameter 65mm 29⁄16"Former: Glass fiberLayers: 4Wire: CCAWNet weight:10.6kg 23.4lbsDriver Displacement 3l 0.1 cu.ft.​​

The EC 165 K kit is composed of two 165 mm (6½") woofers with coaxial tweeters. Like all speaker drivers in the K2 Power line, the coaxial woofers of the EC 165 K kit are equipped with Kevlar® cones. The cones are fixed to the frame using TMD suspension, whose exclusive design removes unwanted resonances and reduces the effects of distortion. The two TKM inverted dome tweeters are composed of aramid fibers. Their exclusive “M”-shaped profile is designed to reinforce dome integrity and to smoothly reproduce high frequencies (up to 22kHz).The kit is supplied with aluminum and mesh grilles.Features:RigidityExcellent dampingDynamic sound and perfect definition. Built-in crossovers​Specifications:Nominal power:15WMaximum power:  100WSensitivity (2,83V/1m) 92dBCone Kevlar sandwichNom. impedance 4ΩSurround;ButylDC resistance; 3.5ΩVC diameter ;20mm 025⁄32"Former; KaptonLayers ;2Wire; AluNet weight; 60g 0.13lbs 

The ES 130 K kit offers great linearity, deep bass and an impressive SPL of 90.8 dB (2.83 V/1 m) in an extremely compact design.This kit is composed of two 5" (130mm) woofers featuring K2 Power Kevlar® cones endowed with the ideal qualities: lightness, rigidity and excellent damping. These speaker drivers deliver an extremely dynamic sound with perfect definition. The cones are fixed to the frame using TMD suspension, whose exclusive design removes unwanted resonances and reduces the effects of distortion.And two 025/32" (20mm) aramid-fibre TKM inverted dome tweeters. Their exclusive &#39;M&#39;- shaped profile is designed to control deformation of the dome, and to perfectly reproduce high frequencies up to 22kHz smoothly and with precision. Their compact crossovers are quick to install and easy to set up. Various accessories are supplied for assembling the tweeters, which can be installed in the factory locations, on tilting frames or flush-mounted.Features:Inverted dome "M"-shaped tweeterHigh linearityHigh SPL (for the size)​Specifications:2-way component kitDiameter: 5" (130mm)Voice coil diameter: 1" (25mm)Voice coil height: 01/2" (12mm)Motor: MagnetTweeter: TKM ("M" profile aramid fiberinverted dome)Cone: Composite K2 Power "W" sandwich coneSurround: Tuned Mass Damper (TMD®)Separated crossover: 6-12/12dB (3.5kHz)Tweeter Adjustable level: +3; 0; -3dB/octMax. power: 160WNom. power: 80W RMSSensitivity (2.83V/1m): 90dBFrequency response: 65Hz- 22kHzImpedance: 4 ΩAccessories: Supplied gril 

The FD 4.350 is the 4-channel model (4 x 58 Watts RMS) and the most versatile of the range. It can operate in 4-, 3- or 2-channel mode. In most cases, it will be used to amplify a car’s front and rear speaker drivers. It can also be used to drive front speaker drivers and a small subwoofer, for a small installation which stays simple and integrated.Features:D Class Amplifier – Direct Fet ® Technology – Thermal efficiency and precisionLow noise operational amplifiers : New Japan Radio ® NJM4580Low ESR capacitors - 105°cPseudo symmetrical inputsHigh level inputs through audio transformersSpecifications:4/3/2-channel D Class amplifierHigh-level inputs with auto-detect / RCAlow-level inputsCEA power (4 Ohms): 4x58 Watts RMSPower max (2 Ohms): 4x100 Watts RMSPower max (4 Ohms bridged): 2x200 Watts RMSConfigurable high-pass/low-pass crossover: 40Hz-400HzFull range modeProtections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / heat protectionDimensions (L x H x W):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85 kg 

The FD 2.350 is a 2-channel model delivering a power of 2 x 105 Watts RMS under 4 Ohms. For a perfect matching, it’s featuring an active high-pass and lowpass crossover. The FD 2.350 can consequently drive a pair of speaker drivers or a subwoofer.Features:D Class – Direct Fet ® Technology - Efficient heat dissipation and precisionStable under 2 OhmsStackable aluminium chassis with high heat dissipationLow noise operational amplifiers New Japan Radio® NJM4580Low ESR capacitors - 105°C (220°F)Pseudo-balanced inputsCable accessories included - easy to install Specifications:Stereo D Class bridgeable amplifierHigh-level inputs with auto-detect / RCAlow-level inputsCEA power (4 Ohms): 2x105 Watts RMSPower max (2 Ohms): 2x170 Watts RMSPower max (4 Ohms bridged): 1x360 Watts RMSConfigurable high-pass/low-pass crossover: 40Hz-400HzFull range modeBass boost (0-12dB)Protections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / over heating protectionDimensions (LxHxW):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85kg 

The FD 1.350 is a mono block amplifier specifically designed for handling a subwoofer channel. It has a power of 210 and 350 Watts RMS under 4 and 2 Ohms respectively. In order to configure the system’s bass according to the car’s installation; it is equipped with an active crossover, bass correction and phase adjustment.Features:D Class Amplifier – Direct Fet ® Technology – Thermal efficiency and precisionLow noise operational amplifiers : New Japan Radio ® NJM4580Low ESR capacitors - 105°cPseudo symmetrical inputsHigh level inputs through audio transformersSpecifications:Mono D Class amplifier with dual outputHigh-level inputs with auto-detection /RCA low-level inputsCEA power (4 Ohms): 1x210 Watts RMSPower max (2 Ohms): 1x350 Watts RMSLow-pass crossover: 40Hz-400HzProgressive phase adjustment (0-180°)Bass boost (0/6dB/12dB)Protections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / heat protectionDimensions (LxHxW):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85kg 

The ES 100 K is an ultra-compact solution with an impressive SPL of 90dB (2.83 V/1 m) for such a small design.It is composed of two 4" (100mm) speaker drivers with Kevlar® cones. The famous yellow cones of the K2 Power line are light, rigid and have excellent damping to provide dynamic sound with incredible definition. The centre of the cone is equipped with a phase plug for improved sound dispersion around the vehicle.The high frequencies are faithfully reproduced by two 025/32" (20mm) TKM tweeters. Composed of aramid fibres, these inverted dome tweeters have an exclusive &#39;M&#39;-shaped profile to control deformation and to reduce distortion. The new-generation tweeters feature very compact crossovers which are easy to install. Various accessories are supplied for assembling the tweeters, which can be installed in the factory locations, on tilting frames or flush-mounted.The size of each component of this kit has been optimised to offer a very compact solution which can be adapted for all kinds of set-ups in all kinds of vehicles.Features:Inverted dome "M"-shaped tweeterNew shape of coneHigh displacementCompact crossoverSpecifications:2-way component kitDiameter: 4" (100mm)Voice coil diameter: 013/16" (20mm)Voice coil height: 01/3" (8.5mm)Motor: NeodymiumTweeter: TKM ("M" profile aramid fiberinverted dome)Cone: Composite K2 Power "W" sandwich coneSurround: Tuned Mass Damper (TMD®)Separated crossover: 12/12dB (3.5kHz)Tweeter Adjustable level: +3; 0; -3dB/octMax. power: 120WNom. power: 60W RMSSensitivity (2.83V/1m): 90dBFrequency response: 110Hz- 22kHzImpedance: 4 ΩAccessories: Supplied grilles​​

The subwoofer’s robustness comes from its compact chassis, and thanks to its ultra-thin design, it fits discretely under a car seat or in the trunk. What’s more, the remote helps you to stay in full control of the subwoofer. Its other strengths are the low-pass crossover and phase adjustment, which enable you to fine-tune your subwoofer to ensure perfect harmony with your audio system.Features:Ready to use (Plug & Play ISO cables supplied)Easy integration in the trunk or under a seatHigh and low level inputsIntensifies the bass frequenciesof your audio systemRemote controlEasy to useSpecifications:Type: Active enclosure with 20cm (8”) subwooferMax. power: 150WNom. power: 75WFrequency response: 45Hz - 150HzHeight: 71.5mm (2.8”)Length: 344mm (13.5”)Width: 250mm (9,8”)

Compact 5" (13cm) subwoofer developed for mounting at the front of the vehicle, 22mm (0.9") high linearity voice coil, Neodynium magnet. High power handling, significant energy contribution in a well limited inner volume environment in order to achieve exceptional bass reproduction.Features:5’’ compact reference subwooferFor superior quality bass in 50 to 100Hz rangeFront mounting in vehicleFor small sealed box (3 to 7 liter)W sandwich composite woofer coneDamping basketUltra high powered Neodymium magnetHigh power handlingSpecifications:Type: 5" (13cm) "W" subwooferFrequency response: (+/- 3dB) 36HzSensitivity: (2.83V/1M) 88dBPower handling: 75W/150WNominale impedance: 4 ohmsVoice-coil diameterP: 11/4" (32mm)Voice-coil height :7/8" (22mm)Xmax: 5/16" (8mm) 

P30F is a 12’’ (30cm) subwoofer designed for a 28,3-liter-closed cabinet or a 40-liter-bass-reflex one. Regarding the performances, it announces 400 Watts RMS and a frequency response from 27 to 500Hz. The largest of the other 2 Flax subwoofers, it provides powerful bass without compromise and high SPL. Performance and high acoustic pressure lovers will be won over by this subwoofer!The three Flax subwoofers consist of straightforward 4-Ohm voice coils which are perfectly suited for small enclosures (closed or bass-reflex). Several innovations raise their performance to an even higher level. Each model has a dual magnet, offering improved linearity and ensuring optimal magnetic power delivered to the voice coil, which features a new cooling system. Glass fiber has been used for the mounting of the voice coil, making it more robust while protecting the cone from the heat emitted. Last but not least, the new fixings connecting the cone to the voice coil and the spider to the basket improve reliability for extreme use (very high excursion).Features:Dual Magnet" for more powerFLAX® technology for an exclusive cone14mm XmaxHigh rigidity for deep and controlled bassImproved excursion thanks to the new suspensionOptimised cooling of the voice coilCompact size for sealed or ported enclosureSpecifications:Woofer: 12" (300mm)Voice-coil: 2" (50mm)Voice-coil hight: 13/8" (35mm)Magnet: 511/16 (145mm)Max. power: 800 WattsNominal power: 400 Watts RMSSensitivity (2.83V/1m): 86.7dBImpedance: 4 OhmsFrequency response: 27Hz - 500Hz

This coaxial kit is the ideal solution for rear speaker drivers for vehicles equipped with Flax component kits in the front (PS 165 F, PS 165 FX, PS 165 F3 or PS 130 F). Indeed, many vehicles only have one location in the rear for a wideband coaxial speaker driver.The PC 165 F can be used to back up your front speaker drivers using the same Flax cone technology for perfectly balanced sound. The PC 165 F can also be installed in the front as a replacement for other coaxial kits.Features:High sensitivityAll the last high tech solutionsUnique and patented FLAX cone (N°1350116)A new sound for a new 100% Focal signatureExponential coneMore compact tweeter supportIntegrated crossoverSpecifications:2-way coaxial kitDiameter: 61/2" (165mm)Voice-coil diameter: 1" (25mm)Voice-coil height: 01/2" (13mm)Motor: MagnetAluminum/Magnesium inverted dome tweeterCone: FlaxIntegrated crossover: 6dB/OctMax. power: 140WNom. power: 70W RMSSensitivity (2.83V/1m): 91.9dBFrequency response: 60Hz – 28kHzImpedance: 4ΩAccessories: Supplied grilles 

P 25 F is a 10’’ (25cm) subwoofer designed for a 18,4-liter- closed cabinet or a 25-liter- bass-reflex one. It is equipped with a very rigid Flax cone of 320 gr/m² which guarantees deep, powerful and linear bass. Its power is 300 Watts RMS and its frequency response goes from 33 to 500Hz. P 25 F Flax subwoofer represent a good compromise between bass pleasure and cabinet volume. The reference in the bass world!The three Flax subwoofers consist of straightforward 4-Ohm voice coils which are perfectly suited for small enclosures (closed or bass-reflex). Several innovations raise their performance to an even higher level. Each model of subwoofer has a dual magnet, offering improved linearity and ensuring optimal magnetic power delivered to the voice coil, which features a new cooling system. Glass fiber has been used for the mounting of the voice coil, making it more robust while protecting the cone from the heat emitted. Last but not least, the new fixings connecting the cone to the voice coil and the spider to the basket improve reliability for extreme use (very high excursion).Features:“Dual Magnet" for more powerFLAX® technology for an exclusive cone14mm XmaxHigh rigidity for deep and controlled bassImproved excursion thanks to the new suspensionOptimised cooling of the voice coilCompact size for sealed or ported enclosureSpecifications:Woofer: 10" (250mm)Voice-coil: 2" (50mm)Voice-coil hight: 13/8" (35mm)Magnet: 511/16 (145mm)Max. power: 600 WattsNominal power: 300 Watts RMSSensitivity (2.83V/1m): 85dBImpedance: 4 OhmsFrequency response: 33Hz - 500Hz

This 2-way component kit with 61/2″ woofers truly bears the Focal signature. The PS 165 V1 is equipped with the same cutting-edge technologies as the other speaker drivers in the Performance line: Polyglass cone, diamond-cut aluminium chassis, phase plug and processed aluminium inverted dome tweeters.The PS 165 V1 car audio kit really makes the difference. It can very easily be used to set up a high-quality customised installation. Its separable crossover, with one part for the woofer, the other for the tweeter, makes it much easier to install. Offering high-fidelity sound and high sensitivity, the PS 165 V1 will ensure you get the best performance, whether you use an amplifier or not.Create your sound thanks to this high-performance car audio kit. The expert engineers at Focal have come up with a high-quality kit which combines power, high-fidelity, durability and a compact design. Offer yourself the best without compromise with the PS 165 V1 speaker driver..Features:Create your own sound in your car with this two-way component kit.Polyglass conePartial horn loading tweeterHigh sensitivityDynamics and neutralityAdjustable tweeter levelsThree tweeter cut-off frequenciesThree tweeter integration possibilitiesSpecifications:Diameter: 61/2” (165mm)Voice-coil diameter: 1” (25mm)Voice-coil height: 07/16” (11.5mm)Magnet: 31/3” (85mm)Processed Aluminum inverted dome tweeterSeparate crossover: 0; -3; -6dBMax. power: 160 WattsNom. power: 80 Watts rmsSensitivity (2.83V/1m): 92.5dBFrequency response: 60Hz – 20kHzAccessories: Supplied grilles

P20F is a 8’’ (20cm) subwoofer equipped with 320 gr/m² Flax cone for deep and controlled bass. It can work in both 10-liter-closed and 13-liter-bass-reflex cabinets. It provides 250-Watts RMS and a frequency response from 39 to 500Hz. This subwoofer is ideal for a small bass enclosure perfectly integrated in the vehicle. The three Flax subwoofers consist of straightforward 4-Ohm voice coils which are perfectly suited for small enclosures (closed or bass-reflex). Several innovations raise their performance to an even higher level. Each model of subwoofer has a dual magnet, offering improved linearity and ensuring optimal magnetic power delivered to the voice coil, which features a new cooling system. Glass fiber has been used for the mounting of the voice coil, making it more robust while protecting the cone from the heat emitted. Last but not least, the new fixings connecting the cone to the voice coil and the spider to the basket improve reliability for extreme use (very high excursion).Features:“Dual Magnet" for more powerFLAX® technology for an exclusive coneHigh rigidity for deep and controlled bassImproved excursion thanks to the new suspensionOptimised cooling of the voice coilThe best compromise for a small seal enclosure volume using (0.35 Cu ft – 10L)Specifications:Woofer: 8" (200mm)Voice-coil: 2" (50mm)Voice-coil hight: 11/8" (28mm)Magnet: 43/4 (120mm)Max. power: 500 WattsNominal power: 250 Watts RMSSensitivity (2.83V/1m): 82.5dBImpedance: 4 OhmsFrequency response: 39Hz - 500Hz