The ATC SCM0.1/12 is a floor loaded active subwoofer using ATC’s 12-inch SL driver powered an impressive 650W amplifier. It is ideally paired with the SCM20ASL Pro. The ATC SCM0.1/12 offers extremely low 3rd harmonic distortion and an impressive 118dB spl at 28Hz. Its floor-loaded design provides a better room adaptation than front-loaded designs.It is designed to be used as the ELF in a multi-channel setup or as bass extender in a two-channel setup.ATC SCM0.1/12 Main Features: Drivers: LF 314mm Amplitude Linearity: +2dB 30Hz - 300Hz Cut-off Frequencies (-6dB free standing) 20Hz Max Continuous SPL @ 1 meter 118dB Amplifier Output: Bass 1000 Watts RMS Overload Protection Active FET Momentary Gain Reduction plus thermal tweeter protection Input Impedance 10k ohms Input Sensitivity 1V Sensitivity Trim +6dB Input Connector Male XLR
The PH3 is a phono preamplification stage intended for use with an active line-level stereo preamplifier. Fully single-ended from input to output, the PH3 uses a combination of J-FET input stage technology (for low inherent circuit noise) and class A operation vacuum-tube gain via three 6922 twin triodes. Total gain of the PH3 is 54 dB (non-adjustable). Used with typical line preamplifiers having 12 to 18 dB of gain, the PH3 is suitable for phono cartridges having .25 mV output or higher. Input impedance is factory-set at 47K ohms, and input capacitance at 90 pF. For optimal matching to moving-coil and moving-magnet phono cartridges, both input impedance and input capacitance may be adjusted via simple resistor and capacitor changes.A resistor kit (with solder) is supplied for proper loading values between 30 and 800 ohms. Additional resistor values and capacitors may be ordered from the factory. On the rear panel, the PH3 provides one pair of gold-plated, audiophile-grade single-ended connectors for L & R inputs, and one pair for outputs. High-quality single-ended interconnects such as Audio Research LitzLink 2 brand are strongly recommended for best sonic performance with the PH3.
The Audio Research Corporation LS22 Line Stage Preamplifier was chosen for this upgrade project because it has a lot of features and a lot of potential. The features that make it attractive are:• The option of either balanced XLR or unbalanced RCA connections for all inputs and the two sets of outputs.• It has a hard wired power cord that many say gives better performance than using a special power cord with extra connections. (see below for Update.)• It is out of production. The acquisition cost was low.• It has a simple signal path and a large, easily accessible circuit board.• The circuit board is of high quality and has heavy and wide traces. This helps with modifications because less damage to the traces is likely to occur when removing components such as capacitors or when soldering in new parts.• The LS22 was the last ARC line stage to be pure tube in the audio signal path, use a normal volume control, and 6922 tubes. The succeeding model, the LS25, included the new and annoying switch-thing “what the @#$% were they thinking?” volume control. The highly rated LS25 mk. 2 used 6H30 tubes, tubes which I have rarely found to be as true to the heart of music’s emotion as the good old 6922/6DJ8 family of vacuum tubes.
The Gold 300 has been engineered to deliver a true audiophile experience. Premium driver technology taken from our flagship Platinum II speakers has been melded with class-leading cabinet construction to produce a speaker designed to last a lifetime.Gold 300 is the pinnacle of the range. Its deceptively large cabinet houses a 2½" (64 mm) C-CAM mid-range driver with a MPD high-frequency transducer above and a pair of 8" (203 mm) RDT II bass drivers below, in a true three-way arrangement.Also featuring a pair of rear-facing HiVe II ports delivering smooth airflow and ample bass reinforcement, Gold 300 is the ideal speaker for larger rooms. Its punch and dynamism are matched only by its subtlety and fidelity – Gold 300’s effortless authority, from a crisp 50 kHz at the top end to an earth-moving 30 Hz at the bottom, makes it perfect for any and all listening requirements.
Condition: ExcellentPackage: YesWarranty: ΝοThe VTL IT-85 Integrated Amplifier is designed for those who seek the simplicity of a single chassis system, but with the performance of separates. Designed with a fully active preamplifier stage, the IT-85 delivers a hearty 60 watts per channel with the sonic characteristic that is similar to our well regarded ST-85 Stereo amplifier and the TL2.5 preamplifier combination – fast, musical 3-D sound, and solid bass support that VTL is known for.The IT-85 is a full linestage preamp and power amplifier in one chassis, and the linestage section has sufficient gain and a buffered output to be able to drive a subwoofer through the preamp out. The headphone section of the IT-85 is driven off the tube output stage and output transformer of the power amplifier section thus making it an ideal high performance pure tube headphone amplifier for headphone aficionados.The IT-85 is designed to accommodate future upgrade — when you are ready to add a subwoofer, separate pre- or power amplifier, surround processor or headphones to your system, the IT-85’s many different output stage configurations can be easily and painlessly re-configured, often with just the flip of a switch. Hand built in our factory in California with the proven VTL quality, the IT-85 will give you lasting value and listening pleasure for years to come.
A superb quality two-way passive magnetically shielded speaker with twin 7-inch glass fiber woofers and an 1-inch Neodymium Ring Radiator Tweeter . One of the best speakers in the world regardless of price, product of the year in the Stereophile magazine. Features : One 1" (25mm) Neodymium Ring Radiator tweeter Two 7" (18cm) Glass Fiber Mid-Woofers in MTM configuration Frequency response: 56Hz-20kHz ±1dB (31Hz-40kHz ±3dB) SPL: 90 dB 1W/1m Impedance: 4 Ohms Dimensions: 23.6" H x 9.4" W x 12.4" D (60cm x 24cm x 32.5cm) Weight: 41 lbs (18.5 kg) * Price for 1 speaker
The Aria 926 embodies the home 3-way floor standing loudspeaker. This musical and expressive loudspeaker is easy to install. All kinds of music lovers will be thrilled with its acoustic qualities. The Aria 926 is by definition an affordable audiophile loudspeaker.It is ideal for rooms measuring from 215ft2 (20m2) and from a recommended listening distance of 10ft (3m).Features:New Flax coneNew TNF tweeterSpeaker drivers developed and manufactured in France by FocalBlack High Gloss and Walnut finishesLeather-finished body
The MK2 Model 12 mkII is designed and precision engineered for pure audio reproduction. The all new highly advanced drive system provides much improved speed control, accuracy and stability. This best-selling and very capable precision turntable has evolved to deliver the perfect listening experience.The Model 12A has been designed for those who would prefer to select their own unique combination of phono stage and cartridge for a more personalised listening experience. This introductory model benefits from the finest materials and craftsmanship found throughout the entire SME turntable and tonearm range. Every component part has been precision engineered in-house to the strictest tolerances to contribute to an outstanding musical performance This exciting entry level turntable uses the unique styling of Synergy and comes complete with the highly acclaimed SME 309 tonearm and internal Crystal Cable wiring as standard. The Model 12A is available in three paint finishes of traditional SME Black, Dark Grey and Dark Blue with contrasting detailing.Speed ControlThe electronic control unit uses a high-performance microprocessor, optimised for motor control. Closed loop speed control is implemented using a proportional plus integral (PI) algorithm. Speed ranges are 33.3, 45 & 78 rpm, with fine pitch speed adjustment allowing increments/decrements of +/-0.01% of the selected speed. The electronic control circuitry and power supply unit are housed in an external one-piece CNC machined case. This new design offers complete isolation and support and is the perfect environment for the electronics. Speed selection controls are mounted on the front facia panel with LED indicators.TonearmDesigned to compliment the Model 309 tonearmCrystal Cable WiringThe Model 12A is equipped with a premium grade signal cable from Crystal Cable which is installed inside the tonearm, connected to phono stage and coupled with the cartridge. Pure mono-crystal silver conductors in miniature format. Providing precious metal in its most pure version, lifting the musical performance to a higher level.
Designed, developed and made in France at the Focal workshops, Aria K2 936 is a revamped and unique edition of the flagship model from the Aria line: Aria 936. The iconic K2 Power cone replaces the Flax cone in the speaker drivers. Manufactured by the Focal teams, this aramid fibre cone delivers a dynamic, powerful sound, in addition to giving Aria K2 936 exceptional character. In a stereo installation, the listening experience speaks for itself, whatever genre of music you like to play. Alongside its impressive performance, the model boasts a modern design, enhanced by the Ash Grey premium finish from the Utopia line and a front panel adorned with an elegant leather effect. Aria K2 936 enhances the pleasure of new listening experiences, with assertive and inimitable style.
This is the REL Strata, which was the 'baby' of the range when released, and basically is a black vinyl cube. It has a downward firing 10" long throw magnesium cast speaker and a low tuned downward port. It also features REL's comprehensive connection inputs and room/main speaker calibration controls. Size is 52H x 42W x 31D cm. Weight 17Kg.
Active subwoofer that uses QD-Bass technology.The unit is equipped with 25 cm cone type woofer.QD-Bass technology is adopted.In this system, the woofer unit is installed downward and a pyramidal diffuser plate is installed on the bottom to efficiently radiate low-temperature energy in four horizontal directions. This realizes smooth frequency characteristics and free setting regardless of installation location.The enclosure uses the Advanced Yamaha Active Serve Technology (A-YST) system.Based on the concept of an air woofer that uses air itself as a diaphragm, the A-YST system enables low-frequency playback equivalent to that of a large speaker even in a small enclosure.There were 2 types of finishes, cherry and black cherry and black.Equipped with an auto standby function.Equipped with a B. A. S. S. mode switch.Movie/Music can be switched, and low sound playback is possible depending on the source.Equipped with a phase selector switch.
A true reference thanks to the precision of the stereo image, its capacity to reproduce each of the micro details of the audio signal , as well as unconditional respect of the original dynamics.One of the major SM9 innovations lies in the fact of offering 2 monitoring speakers in only one and unique cabinet. The SM9 is thus composed of 2 monitors: a 3 way monitor and a 2 way monitor.Focal SM9 Main Features:Active 3-Way design w/ addition of a specially designed 11-inch passive radiator for improved accuracy in sub-bass reproduction over other designsDrivers feature Focal's now famous "W" composite sandwich cone technologyBeryllium tweeters ensure the fastest, most accurate, and least annoying high frequency reproductionGuaranteed to make you the envy of all your engineering friends... especially once they hear your mixesFocal SM9 Studio Monitor (Single) Specifications:Frequency response : 3-way mode : 30Hz - 40kHz (+/- 3dB) / 40Hz - 20kHz (+/- 1dB) - 2-way mode (Focus) : 90Hz - 20kHz (+/- 3dB)Maximum SPL : 3-way mode : 116dB SPL (peak @ 1m) / 2-way mode (Focus) : 106dB SPL (peak @ 1m)Input : Type / Impedance : Electronically balanced / 10 kOhms / Connector : XLR / Sensitivity : Adjustable, +4dBu or -10dBVBass : 400W, class ABMidrange- : 100W, class ABTreble : 100W, class ABPower supplies : Local supply : 230V (3.15A fuse), 115V (6.3A) - Connection: IEC inlet and detachable power cordIndicators :Rear panelInput sensitivity selector (+4dBu / -10dBV)High-pass crossover (full range, 45, 60, 90Hz @ -6dB)Low frequency shelving(+/- 3dB from 30 to 250Hz per step of 0.5dB)High frequency shelving(+/- 3dB from 4.5 to 40kHz per step of 0.5dB)Low frequency EQ(+/- 3dB per step of 0.5dB @ 50Hz, Q factor = 2)Low-mid frequency EQ(+/- 3dB per step of 0.5dB @ 160Hz, Q factor = 1)Mid frequency EQ(+/- 3dB per step of 0.5dB @ 1kHz, Q factor = 0.6)Side panelStand By / On switchDirect switchFocus switchwarning light : Power On, clipping and default on front panel LEDPassive radiator : 11WPP52, 11” (27cm) Focal “W” composite sandwich cone piston, extra wide inverted surround radiatorSubwoofer: 8W7571, 8” (20cm) Focal “W” composite sandwich cone driverMidrange : 6W0452, 6.5” (16.5cm) Focal “W” composite sandwich cone driverTweeter : TB872, 1” pure Beryllium inverted dome tweeterConstruction : 0.88”(22mm) and 1.2” (30mm) panels with internal bracesFinish : Black natural veneering top and bottom panels, black bodyDimensions : 12.8” x 19.6” x 15.6” (320mm x 490mm x 390mm)Net weight : 77lb (35kg)
It’s been almost 30 years since we designed our first integrated amplifier: time enough to define and refine the technical ingredients essential to high-end performance. Our reference quality SUPERNAIT 2 represents the pinnacle of this accumulated knowledge. It is both the most sophisticated integrated amplifier we’ve ever created and a classic Naim Audio product, shot through with the soul of the original, iconic NAIT.SUPERNAIT 2 combines an 80W power amplifier with six individually decoupled input sockets and borrows advanced technology from Naim Audio’s flagship preamplifier, the NAC 552. In employing the latest Naim Audio DR (Discrete Regulator) circuits in its power supply, it sits right at the forefront of Naim Audio amplifier technology.
Integrated Amplifier with DAC, DSD, Phono, Airplay, Bluetooth and LAN !M-One is not only an integrated amplifier, but a window into a unique musical experience …No single audio product before the M-One delivers such a feature-packed and modern product that fits into such a small and elegant space – crafted from a single block of Aluminum.Essentially, it's an integrated amplifier, but with every connection you could want. Against all the odds, our engineers have managed to incorporate all the latest connections – Bluetooth aptX, LAN-Network 24bit /384kHz Asynchronous, SPDIF Coax-Opto-AES 24bit / 768kHz USB asynchronous passing DXD, DSD, DOP…, Phono MM / MC, Analog balanced and unbalanced inputs, and DSP with automatic room correction. Analog Balanced and Unbalanced Inputs, are just some of the inclusions.It is often the most demanding constraints that inspire engineers and designers to strive for creative and innovative solutions. Our tailor made M-One integrated amplifiers are a perfect example (M.C.F.) !Good Things Come in Small PackagesGet iOS App >Get Android App >Common audio wisdom dictates that high fidelity is best achieved with separate components, discreet circuitry, and space-consuming electronics and cables. However, this conventional wisdom is not without exception. Seeming contradictions exist where products have been able to produce the same phenomenal sound in a much smaller electronic package.This appears to be the logic behind the brand Micromega, whose paradoxical name has been associated with high-quality audio in unique packages since 1987. The company’s new M-One range of integrated amplifiers lives up to this legacy, offering a sleek and compact visual with a shocking array of connectivity options. It should go without saying that sound quality is at the forefront of the design. The device includes a DAC that is compatible with all high-resolution audio formats, a phono stage for turntables with both moving-magnet and moving-coil cartridges, power amplifier for loudspeakers, and many other options.The rear panel of the device has 26 connections, what one would expect from a mainstream A/V receiver rather than an audiophile integrated amplifier. Micromega touts that the device is encased in a cabinet milled from a single block of aluminum, and it comes in a variety of colors to suit the listener’s preferences. The M-One is sure to satisfy even the pickiest room designer or audiophile.It’s an absolute engineering miracle!Since your listening room is the weakest link in your installation, our engineers designed the M.A.R.S system to address this issue.This acoustic correction system and its Room EQ program detect the sound irregularities of your room and attenuate them for a balanced and accurate response. Over time, the dedicated application will provide this scalable system with a variety of additional features* MARS is included with M-150, in option with M-100* Premium Gloss finishes available for an additional $1000.00 SPECIFICATIONS* AMPLIFIER - classe AB* DAC PCM 32/768 et DSD256* DLNA* Ethernet* Bluetooth SBC - apt-X* S/PDIF - I2S* USB asynchronous* Calibration microphone M.A.R.S (optional)* Phono : MM / MC* 1.4 Vrms (RCA) - 1.7 Vrms (XLR)* 1x USB type B* 2x USB type A (service)* 2x HDMI I2S* 1x S/PDIF optique Toslink* 1x S/PDIF coaxiale RCA* 1x trigger* 1x INPUT XLR* 1x INPUT RCA* 1x phono MM/MC* 1x microphone* 1x pre-out XLR* 1x RCA* 1X SUB OUT* POWER : 2x100 W (8 Ohms) et 2x200 W (4 Ohms)* Rapport signal /bruit : 100 dB (RCA), 103 dB (XLR) et > 75 dB (phono)* SEPARATION: 96 dB @ 1 kHz et 80 dB @ 10 kHz430 x 56 x 350 mm10.7 kg
The heart of any home cinema system, the Q 3090Ci has been developed to compliment the 3000i series perfectly, bringing crisp and clear dialogue and onscreen sound to life, using the latest technological enhancements applied to the full 3000i series. Key Features Accurate Centre speaker with precision drivers can be shelf or cabinet mounted on pre-fitted rubber feet or wall-mounted on optional, dedicate brackets. The normal terminal panel cut-out has been removed, giving greatly improved structural integrity to the enclosures and new low profile binding posts The 3090Ci is the same width as most Amplifiers and AV Receivers so will fit attractively into the specialist furniture designed to house them. The Centre Of Your Home Cinema Setup The Q 3090Ci boasts twin 100mm (4”) and 22mm (0.9”) precision drivers delivering the ultimate cinematic experience. You will hear every precise detail; every note, every word at its very best. The Q 3090Ci incorporates the same technology used across the rest of the 3000i range including P2P bracing and brand new high frequency drivers ensuring it complements the rest of the series, perfectly. Dynamic & Detailed With the new high frequency driver unit, the Q 3090Ci benefits from a decoupled tweeter which ensures the vibrations from the woofer, which can impair the performance of the tweeter, are isolated allowing the tweeter to perform with dramatically reduced interference, resulting in a purer sound. The all new mid/bass drive unit boasts a precision formed cone from impregnated and coated paper and teamed with a newly developed, low-hysteresis, rubber surround also contributing to unwanted resonances. Easy Room Positioning The 3090Ci is the same width as most Amplifiers and AV Receivers so will fit attractively into the specialist furniture designed to house them. The conventional terminal panel cut-outs have been removed, giving greatly improved structural integrity to the enclosures and new low profile binding posts have been incorporated with sockets deep enough to accept 4mm (0.16 in) Banana Plugs. Beautiful Inside And Out Not only does the entire 3000i range features all new enclosure aesthetics but it also offers 4 new contemporary finishes. The new 3000i series speakers are available in four standard finishes; Graphite Grey, English Walnut, Carbon Black or Arctic White. All are finished with an attractive chrome bezel around each driver and feature magnetic speaker grilles.
Small but powerful!Two-way bass-reflex satellite loudspeaker. Dive into the universe of Sib Evo, the evolution of the iconic Sib & Co range! These small loudspeakers will blend in everywhere thanks to their timeless and futuristic design. Let yourself be blown away by their quality and the power of their sound despite their small size! Sib Evo delivers significant acoustic power. So, the volume can be loud, without it ever being restrained by the size of the amplifier. It will add a new audio dimension to your ambiance music, multi-room system or Home Cinema setup.The audio track will perfectly render the music, as well as the dialogue and the full intensity of the action or the emotion. All the key elements of the film are conveyed with extreme clarity and pitch-perfect precision, giving you the impression of being right at the heart of the action.This satellite loudspeaker will truly revolutionise your Home Cinema! Combined with the Cub Evo subwoofer in a 5.1 pack, it can also be installed with the Sib Evo Dolby Atmos®, giving you a Home Cinema system with a completely new dimension. A revolution for your films! It can be installed on furniture, mounted to its stand, or fixed to a wall using a mounting system.
Utopia are THE reference high-fidelity headphones manufactured in France by Focal. They are the result of 35 years of innovation, development and manufacturing of high-end speaker drivers and loudspeakers.Equipped with exclusive technology, they offer striking realism, neutrality, dynamics and clarity, for sound with unrivalled purity. Utopia are equipped with totally open-backed full-range speaker drivers with pure Beryllium ‘M’-shaped domes. Once more, the engineers at Focal have pushed back the limits of acoustic innovation and have succeeded in providing a listening experience worthy of the best Focal loudspeakers. The result: a transducer with a frequency response ranging from 5Hz to more than 50kHz without any crossover or passive filtering! You’ll completely forget you are wearing these headphones, and the reproduction of the audio signal is of unrivalled purity.They meet all the requirements expected of high-end headphones due to their sophisticated and elegant design and to purposeful materiality, such as the carbon fibre yoke and the Pittards® Leather ear cushions. Particular attention has been paid to the design of Utopia, in terms of use, comfort and overall aesthetics. These audiophile headphones feature elegant, high-quality materials, and comfort has been greatly enhanced thanks to the mechanical design which has been optimised to the smallest detail: the constant bend of the headband, an even distribution of weight, the design of the yoke and the memory foam ear-pieces. The cable supplied with Utopia was specifically selected for its capability to respect the original audio signal, such as its very low impedance (< 90 mΩ/metre). It is totally symmetrical in order to offer extremely low crosstalk (< 70 picofarads). The shielding protects it from electromagnetic interference and allows for a longer cable (4m/13 ft.). Finally, the 9.5mm Lemo® connector and the 6.35mm Neutrik® stereo jack enable easy customisation.
The XPS is a simple and effective upgrade to enhance the music-making ability of your Naim Audio source component. As one of our most flexible performers it can be used to upgrade our CDX2 CD player and DAC digital to analogue converter, and it is also suitable for use with our NDS, NDX and ND5 XS network players and HDX hard-disk player/server. Its large toroidal transformer features four separate windings, coupled to six low-noise regulators and benefits from Naim Audio DR voltage regulator technology Features: Four isolated transformer windings with six low-noise DR power regulators - configured as two isolated regulators for digital at +15V, isolated +/-10V for DACs and isolated +/-23V for analogue stages All-new Discrete Regulator (DR) configuration, delivering Naim Audio’s best-ever standards of stable, low-noise power Brushed, black-anodised aluminium chassis plus anti-vibration feet Technology & Craft The Naim Audio XPS is a highly sophisticated power supply with six separately regulated, very low noise outputs, featuring a toroidal transformer and six power regulators. These supplies are branched and re-regulated, some twice in the CD player. The addition of anti-vibration, resonance-controlling feet complement the elegant cast and extruded anti-magnetic chassis protect the sensitive internal components from resonance and microphonic vibration. The XPS was updated in 2012 as a result of a two year project to develop a new discrete regulator (DR) for Naim Audio power supplies. The new Naim Audio DR now features, alongside improvements to the mechanical decoupling and internal layout. These enhancements, developed through intensive listening tests, significantly raise performance and make music even more communicative and enjoyable. Please note Only new classic series XPS units are compatible with the NDX network player, not ‘Olive’ versions. The old ‘Olive’ XPS is still compatible with CDX and CDS model CD players, the HDX hard disk player and the DAC digital to analogue converter however. Please consult your Naim Audio retailer if you are unsure of compatibility. Finish: Case: Black powder coated Front: Brushed and black anodised Outputs: Power Outputs: ± 22V, ± 10V, 2 x 15V Physical: Shipping Weight: 15.1 kg Shipping Dimensions: 240 x 590 x 500mm Weight: 12.4 kg Dimensions (HxWxD): 87 x 432 x 314mm Power: Mains Supply: 100V, 115V, 230V; 50 or 60Hz Supplied with: Supplied with: Burndy Upgrades: Other: Power-Line Lite mains cable (UK denominations only)
The NAC-N 272 combines our digital audio technology with classic analogue preamplifier engineering. It samples the best of both worlds to create an immensely musical hi-fi system. Paired with a NAP 200, NAP 250 or even a NAP 300 power amplifier, the 272 is an ideal choice for those seeking the convenience of a single box streaming system with iOS and Android app control, but that crave hi-fi separates performance. It boasts an impressive array of inputs including high-resolution (up to 24bit/192kHz) UPnPTM streaming, Spotify Connect, iRadio, Bluetooth (aptX), USB, multiroom, TIDAL music streaming support and an optional DAB/FM module. Six digital and three analogue inputs cover integration with a wide range of sources from CD and games consoles to phonostages. It’s also performance upgradable with the addition of a Naim Audio XP5 XS, XPS or 555 PS power supply. All this functionality does not come at the cost of performance. The 272 has been carefully designed and meticulously hand-crafted to deliver a completely immersive and awe-inspiring music experience. Features: High quality preamplifier including digitally controlled analogue volume control UPnP-enabled to allow streaming of audio files at up to 24bit/192kHz resolution from Naim Audio hard disk servers, network-attached storage (NAS) devices or any home computer Performance upgradable with XPS or 555 PS power supply Supports a broad range of music formats: WAV, FLAC, Apple Lossless, AIFF, AAC, DSF64 and DFF64, Windows Media-formatted files, Ogg Vorbis and MP3 Six 24bit/192kHz-capable digital inputs (S/PDIF) to support optimum connection to external sources Spotify Connect built-in to stream millions of songs from the world’s most popular streaming service Native support for TIDAL streaming service with free 90 day trial of lossless HiFi tier Bluetooth connectivity with aptX audio codec Optional DAB+/DAB/FM radio module vTuner 5* full-service internet radio Multiroom & Party Mode compatible Naim Audio app for iOS and Android Hand-built in Salisbury England All analogue input sockets on the 272 are individually hand wired to the main board to enhance mechanical decoupling. The board itself is mounted on a system of shoulder bolts which releases any tension which can adversely affect sound quality. The sound critical resistors used arrive at Naim Audio matched to within 5%. This already high tolerance is improved before assembly by hand-matching to within margin of just 1%. We then go even further by introducing a slight mechanically compliant bend in the legs of each one during assembly. We take this care and attention because we know it can help to make the difference in producing the incredible sound on which we’ve built our reputation. Hybrid Volume Control & Class-A Headphone Amp The 272 volume control is derived from the design of the flagship Statement NAC S1 control. It offers smooth operation and perfect level matching while a Class-A single-ended headphone amplifier makes the most of high-performance headphones. As soon as headphones are plugged in, the output current drive is automatically turned up five times to give dynamic drive for all headphone impedances. Analogue Preamplifier The NAC-N 272 is a high-performance Naim Audio preamplifier with quality hand-matched analogue components selected after listening tests. Great care has been taken to protect the signal path from sources of interference. The digital and analogue sections of the product communicate using optical isolation chips which minimises the impact of the noisy digital circuitry and power supply on the critical audio components. Digital Technology The 272’s digital pedigree is formidable. It shares the incredibly powerful DSP (Digital Signal Processor) used by the reference NDS network player and features Naim Audio’s proprietary digital audio buffering and filtering techniques. This helps to eliminate jitter and optimises the audio stream for the best musical performance from any digital source. It also means that the 272 can play back DSD64 files.
This preamplifier is the center of your high-end stereo system as well as your multi-channel equipment. It guarantees sonic perfection for stereo playback lovers as well as the friends of multimedia experiences. A preamplifier which combines the exacting demands of a top class high-end stereo preamplifier with the connection and control range of a multimedia device for the first time. All this combined in a stunning and perfectly crafted technical work of art called: No.22 Cineast The input control takes place on the decibel precisely over the two existing multi-function switches for programming and setup, in typical AARON design. The twisted cone of solid material and the blue power indicator are embedded in the 10 mm thick aluminum front.You can control playback for 8 devices, such as a CD player, tuner, DVD, multi-channel equipment and a recording device, in the ideal manner with this preamplifier. Including the 2, a total of 6 output channels are available for mandatory outputs for high-end stereo playback. Our AARON sales representatives will happily inform you of the functions and uses that are ideal for you in stereo, bi-amping or even multi-channel operation.
Description: Three-way, floorstanding loudspeaker with treble and midrange horns, integral powered sealed-box woofer. Drive-units: inverted-dome tweeter loaded with 5.1"-diameter (130mm) horn, dome midrange driver loaded with 19.7"-diameter (500mm) horn, two 10" (250mm) cone woofers. Crossover frequencies: 300Hz, 3kHz. Frequency range: 300Hz–20kHz (midrange/treble), 18–300Hz (woofer). Sensitivity: >104dB. Nominal impedance: 8 ohms. Recommended power: >10W. Power handling: 50W. Subwoofer amplifier power: 250W.Dimensions: (including subwoofer) 50" (1270mm) H by 19.7" (500mm) W by 25.5" (520mm) D. Weight: 157 lbs (68kg).Finishes: Horns: Red, Blue, Silver, Black Pearlescent White (all metallic lacquers); other options available at additional cost. Subwoofer: Nextel Black.Read more at https://www.stereophile.com/content/avantgarde-acoustic-uno-nano-loudspeaker-specifications#Vt0E6mptifqgtzSm.99 Frequency Response: 22Hz to 20kHz Power Handling: 100W Recommended Amplifier: 10W (minimum) Crossover Frequency: 170, 2000Hz Impedance: 8Ω Sensitivity: 101dB Midbass: 1 x horn Tweeter: 1 x horn Dimensions: 670 x 680 x 1700mm Weight: 40kg
JBL JRX 225. Dual JBL low frequency drivers with a 64 mm (2.5 in) diameter edgewound ribbon voice coil which provides more crosssectional wire area in the voice coil gap than round wire designs, for greater efficiency and power handling. JBL 2414H-C 25 mm (1 in) polymer diaphragm compression driver improves high frequency performance as well as system reliability.Attractive 18-gauge hexagon perforated, steel grille protects components from damage. The advanced network topology crossover design shapes frequency response and delivers coherent summation in the crossover region. - High-voltage capacitors and inductors with massive cores and heavy gauge wire enable the crossover network to handle high power without saturating. Progressive Transition? high frequency waveguide provides superior coverage control, reduced distortion, and smoother frequency response.The rugged, acoustically superior enclosure is constructed from 19 mm (.75 in) MDF (Medium Density Fiberboard) using advanced adhesives and mechanical fastener technology for extreme durability and improved low-frequency performance. - SonicGuard? protects the highfrequency driver from excess power without interrupting the performance. Non-resonant, all-steel handles are used.Specifications:Power Rating500 / 2,000 WFrequency RangeAt -10 dB : 36 Hz to 19 kHzFrequency ResponseAt ±3 dB : 45 Hz to 16 kHzSensitivity100 dB SPL (1 W / 1 m) (1m)Nominal Impedance4 ΩAmplifier Power500 to 1000 W into 4 ΩMaximum SPL133 dBNominalDispersion: 90 x 50ºCrossover Frequency2 kHzHigh Frequency DriverJBL 2414H-C 1" (25 mm) polymer diaphragm compression driver mounted on Progressive Transition WaveguideLow Frequency Driver2 x JBL M128Input Connectors1 x Neutrik Speakon NL-4; 0.25" (6.35 mm)1 x TS phone jack; parallelDimensions (H x W x D)43.0 x 18.3 x 16.8" (1,092.0 x 464.0 x 426.0 mm)Weight94 lb (42.6 kg)