B-STOCK

The ATC SCM0.1/12 is a floor loaded active subwoofer using ATC’s 12-inch SL driver powered an impressive 650W amplifier. It is ideally paired with the SCM20ASL Pro. The ATC SCM0.1/12 offers extremely low 3rd harmonic distortion and an impressive 118dB spl at 28Hz. Its floor-loaded design provides a better room adaptation than front-loaded designs.It is designed to be used as the ELF in a multi-channel setup or as bass extender in a two-channel setup.ATC SCM0.1/12 Main Features:    Drivers: LF 314mm    Amplitude Linearity: +2dB 30Hz - 300Hz    Cut-off Frequencies (-6dB free standing) 20Hz    Max Continuous SPL @ 1 meter 118dB    Amplifier Output: Bass 1000 Watts RMS    Overload Protection Active FET Momentary Gain Reduction plus thermal tweeter protection    Input Impedance 10k ohms    Input Sensitivity 1V    Sensitivity Trim +6dB    Input Connector Male XLR

The PH3 is a phono preamplification stage intended for use with an active line-level stereo preamplifier. Fully single-ended from input to output, the PH3 uses a combination of J-FET input stage technology (for low inherent circuit noise) and class A operation vacuum-tube gain via three 6922 twin triodes. Total gain of the PH3 is 54 dB (non-adjustable). Used with typical line preamplifiers having 12 to 18 dB of gain, the PH3 is suitable for phono cartridges having .25 mV output or higher. Input impedance is factory-set at 47K ohms, and input capacitance at 90 pF. For optimal matching to moving-coil and moving-magnet phono cartridges, both input impedance and input capacitance may be adjusted via simple resistor and capacitor changes.A resistor kit (with solder) is supplied for proper loading values between 30 and 800 ohms. Additional resistor values and capacitors may be ordered from the factory. On the rear panel, the PH3 provides one pair of gold-plated, audiophile-grade single-ended connectors for L & R inputs, and one pair for outputs. High-quality single-ended interconnects such as Audio Research LitzLink 2 brand are strongly recommended for best sonic performance with the PH3.

The Audio Research Corporation LS22 Line Stage Preamplifier was chosen for this upgrade project because it has a lot of features and a lot of potential. The features that make it attractive are:• The option of either balanced XLR or unbalanced RCA connections for all inputs and the two sets of outputs.• It has a hard wired power cord that many say gives better performance than using a special power cord with extra connections. (see below for Update.)• It is out of production. The acquisition cost was low.• It has a simple signal path and a large, easily accessible circuit board.• The circuit board is of high quality and has heavy and wide traces. This helps with modifications because less damage to the traces is likely to occur when removing components such as capacitors or when soldering in new parts.• The LS22 was the last ARC line stage to be pure tube in the audio signal path, use a normal volume control, and 6922 tubes. The succeeding model, the LS25, included the new and annoying switch-thing “what the @#$% were they thinking?” volume control. The highly rated LS25 mk. 2 used 6H30 tubes, tubes which I have rarely found to be as true to the heart of music’s emotion as the good old 6922/6DJ8 family of vacuum tubes.

The Gold 300 has been engineered to deliver a true audiophile experience. Premium driver technology taken from our flagship Platinum II speakers has been melded with class-leading cabinet construction to produce a speaker designed to last a lifetime.Gold 300 is the pinnacle of the range. Its deceptively large cabinet houses a 2½" (64 mm) C-CAM mid-range driver with a MPD high-frequency transducer above and a pair of 8" (203 mm) RDT II bass drivers below, in a true three-way arrangement.Also featuring a pair of rear-facing HiVe II ports delivering smooth airflow and ample bass reinforcement, Gold 300 is the ideal speaker for larger rooms. Its punch and dynamism are matched only by its subtlety and fidelity – Gold 300’s effortless authority, from a crisp 50 kHz at the top end to an earth-moving 30 Hz at the bottom, makes it perfect for any and all listening requirements.

Κατάσταση: Άριστη Συσκευασία: ΝαιΕγγύηση: ΌχιThe VTL IT-85 Integrated Amplifier is designed for those who seek the simplicity of a single chassis system, but with the performance of separates. Designed with a fully active preamplifier stage, the IT-85 delivers a hearty 60 watts per channel with the sonic characteristic that is similar to our well regarded ST-85 Stereo amplifier and the TL2.5 preamplifier combination – fast, musical 3-D sound, and solid bass support that VTL is known for.The IT-85 is a full linestage preamp and power amplifier in one chassis, and the linestage section has sufficient gain and a buffered output to be able to drive a subwoofer through the preamp out. The headphone section of the IT-85 is driven off the tube output stage and output transformer of the power amplifier section thus making it an ideal high performance pure tube headphone amplifier for headphone aficionados.The IT-85 is designed to accommodate future upgrade — when you are ready to add a subwoofer, separate pre- or power amplifier, surround processor or headphones to your system, the IT-85’s many different output stage configurations can be easily and painlessly re-configured, often with just the flip of a switch. Hand built in our factory in California with the proven VTL quality, the IT-85 will give you lasting value and listening pleasure for years to come.

Class A και Recomended Component στο περιοδικό Stereophile, στην  ίδια  "λίγκα " με τα καλύτερα ηχεία που κατασκευάστηκαν ποτέ. Ηχείο με  δύο glass fiber γούφερς 7 ιντσών και 1 ίντσας Neodymium Ring Radiator Tweeter. " ... the best loudspeaker I ever heard ..."  σύμφωνα με τον Bob Katz διάσημο mastering engineer Ένα ηχείο που πρέπει να ακούσει κάποιος για να καταλάβει πόσο κοντά στην αληθινή μουσική μπορεί να φτάσει η ακρόαση  ενός συστήματος ηχείων.             ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ : Ενα 1" (25mm) Neodymium Ring Radiator tweeter Δύο 7" (18cm) Glass Fiber Mid-Woofers σε MTM διάταξη Απόκριση συχνοτήτων : 56Hz-20kHz ±1dB (31Hz-40kHz ±3dB) SPL: 90 dB 1W/1m Αντίσταση: 4 Ohms Διαστάσεις: 23.6" H x 9.4" W x 12.4" D (60cm x 24cm x 32.5cm) Βάρος: 41 lbs (18.5 kg)               ΦΙΛΟΣΟΦΙΑ ΚΑΤΑΣΚΕΥΗΣ: 1. A sealed enclosure tuned for the best impulse response rather than a low-end extension. We strongly believe that various kinds of vented enclosures always cause coloration that does not deliver reference accuracy. 2. Sturdy enclosure made of 1" (25mm) thick MDF with internal bracing to bring unwanted resonance and box coloration to an almost nonexistent level. 3. Stiff Glass Fiber Cone mid-woofers with low dampening rubber surround, diecast chassis, and a low distortion magnet. 4. Neodymium Ring Radiator - super low distortion tweeters with frequency response up to 40kHz and extra wide dispersion. 5. The absence of a grill in front of the tweeter. Our laboratory and listening tests prove that even the most transparent grill fabric causes high frequency comb filtering. 6. An acoustic, rather than an electronic, time-coherence of tweeters. 7. Unique tweeter surrounding. Perfecting the tweeter environment appeared quite possibly to be the most challenging aspect of the design. The goal was to eliminate the edging effect by carefully shaping the tweeter surrounding with specially designed Belgian foam. 8. A low-order crossover for the best phase response. We also selected the lowest possible crossover point to deliver the best transient response. 9. Premium quality crossover parts. Foil Inductors wound on a wooden core - with their skin effect conductivity - provide performance unmatched by less expensive wire wound coils, and provide much lower coloration than iron core inductors. We also use non-inductive resistors, premium audiophile grade capacitors and special flat, Super OFC internal wires. 10. Matching internal dampening design. Internal dampening is outsourced and precut to absolutely identical shape and weight for the best speaker-to-speaker consistency. 11. Dual, all-brass, gold-plated posts, which accept banana plugs or up to 2 AWG wires. 12. Magnetic Shielding. All our speakers are magnetically shielded for demanding pro video applications. 13. All parameters perfected in anechoic chamber.

This is the REL Strata, which was the 'baby' of the range when released, and basically is a black vinyl cube. It has a downward firing 10" long throw magnesium cast speaker and a low tuned downward port. It also features REL's comprehensive connection inputs and room/main speaker calibration controls. Size is 52H x 42W x 31D cm. Weight 17Kg.

Active subwoofer that uses QD-Bass technology.The unit is equipped with 25 cm cone type woofer.QD-Bass technology is adopted.In this system, the woofer unit is installed downward and a pyramidal diffuser plate is installed on the bottom to efficiently radiate low-temperature energy in four horizontal directions. This realizes smooth frequency characteristics and free setting regardless of installation location.The enclosure uses the Advanced Yamaha Active Serve Technology (A-YST) system.Based on the concept of an air woofer that uses air itself as a diaphragm, the A-YST system enables low-frequency playback equivalent to that of a large speaker even in a small enclosure.There were 2 types of finishes, cherry and black cherry and black.Equipped with an auto standby function.Equipped with a B. A. S. S. mode switch.Movie/Music can be switched, and low sound playback is possible depending on the source.Equipped with a phase selector switch.

Graded Hammer Action Keyboard88 note, fully weighted graded hammer action keyboard with adjustable touch sensitivity.20 Inspiring Factory PresetsFeaturing some of the the best sounds from our PC3 series, including the famous Kurzweil Triple Strike Grand Piano as well as top notch electric pianos, orchestral and acoustic instruments.29 Rhythm Accompaniment PatternsPre-recorded drum tracks in a variety of styles to play along with.Modern Cabinet DesignSpinet-stye cabinet available in simulated rosewood or white finishes, featuring a 15 Watt, 2-speaker, stereo sound system, built-in music stand and slide-out fallboard.Simple and Intuitive ControlsElegant control panel featuring easy access to all system functions, including Split/Layer, Transpose and One-Touch Favorites.Built-In PedalsSustain, Sostenuto and Soft Pedals standard.

Ηχεία B-Stock: Επιστροφή από πελάτη σε άριστη κατάσταση.Αρχική συσκευασία: ΌχιΕγγύηση: 2 ΧρόνιαΤο νέο ηχείο της Focal Chora 816, είναι ένα ηχείο δαπέδου 2.5 δρόμων με πλούσια μπάσα.Τα woofer του και ο οδηγός των μεσαίων-χαμηλών, διαθέτουν τον καινούριο κώνο της Focal με την τεχνολογία Slatefiber, δουλεύουν σε τέλεια αρμονία για υπέροχη αναπαραγωγή ήχου και τέλεια απόκριση στα χαμηλά. Ο ήχος απλώνεται ομοιόμορφα στην αίθουσα ακρόασης, με δυναμική μεσαία περιοχή και αξιοσημείωτη ισχύ στις χαμηλές.Η μπροστινή οπή στο μεγάφωνο μειώνει την παραμόρφωση και χάρη στην κλίση της βάσης ,η Time Alignment παρέχει ένα ηχητικό πεδίο εστιασμένο στον ακροατή. Το νέο Chora 816 είναι εξαιρετική επιλογή και για Home Cinema εφαρμογές ακούγοντας έναν πλούσιο και ζεστό ήχο σε δωμάτια μέχρι 30m².Tweeter TNF Αλουμινίου / Μαγνησίου - μαλακά και με ακρίβεια πρίμα.Στην κατασκευή του τοιχώματος του tweeter διαθέτει ένα αφρώδες υλικό που ονομάζεται Poron. Αυτό το υλικό χρησιμοποιείται στο διάσημο tweeter Beryllium του Utopia και μειώνει την παραμόρφωση κατά ένα τρίτο μεταξύ 2.000Hz και 3.000Hz εκεί που έχουμε την μεγαλύτερη ευαισθησία του ανθρώπινου αυτιού.Η πολύ μεγάλη κατευθυντικότητα του ανεστραμμένου θόλου επιτρέπουν την μέγιστη ποιότητα ακρόασης από οποιοδήποτε σημείο του σαλονιού και αν ακούτε.Εξαιρετικά ισορροπημένος ήχος - Ο κώνος από SlatefiberΗ τεχνολογία Slatefiber, αποκλειστικότητα της Focal, περιλαμβάνει τη χρήση ανακυκλωμένων ινών άνθρακα που εφαρμόζονται ως σάντουιτς μεταξύ δύο στρωμάτων θερμοπλαστικού πολυμερούς. Στην προσπάθειά για τελειότητα, οι μηχανικοί της Focal επέλεξαν να χρησιμοποιήσουν ίνες άνθρακα, που καταφέρνουν να επιτύχουν ακόμη μεγαλύτερη ακαμψία και μέγιστη απόσβεση. Κατασκευασμένο στα εργαστήρια μας με τα νέα υπερσύγχρονα εργαλεία της εταιρίας, το μεγάφωνο από "σχιστόλιθο" παρέχει καλύτερη απόσβεση και ακαμψία, σε συνδυασμό με την ελαφρότητα - τα τρία "βασικά" στοιχεία που διακρίνουν ένα καλό μεγάφωνο.Κομψό και μοντέρνο σχέδιοΗ σειρά Chora προσφέρει ένα μοντέρνο σχεδιασμό, με υψηλά σχεδιαστικά standards.Η βάση (προαιρετικά) είναι κεκλιμένη για σωστό Time Alignment και παρέχει βέλτιστη στερεοφωνική εικόνα, πιο εστιασμένη στον ακροατή.

Tο νέο ηχείο  της Focal  φιλοδοξεί να είναι το σημείο αναφοράς για την ακρίβεια της στερεοφωνικής εικόνας, της δυνατότητας να αναπαράγει με ακρίβεια τις μικροδυναμικές της μουσικής και να διατηρεί μια πολύ εκτεταμένη δυναμική περιοχή. Με βάρος 35 κιλά παρά το  μικρό σχετικά  μέγεθος , διαθέτει τουίτερ βιρυλίου νέας γενιάς με εξαιρετικά χαρακτηρηστικά (όπως magnet field 2.1 tesla). Επίσης διαθέτει μεγάφωνο μεσαίων 6.5″ , woofer 8.5″ καθώς και ένα passive radiator μεγάφωνο  11″ στο πάνω μέρος της καμπίνας.Οι 3 ενισχυτές είναι αναλογικοί  τάξης AB με πολύ καλά audiophile υλικά και παρουσιάζει εκτεταμένη απόκριση συχνοτήτων απο  30 Hz έως 40 kHz. Για το μπάσο ο ενισχυτής είναι  400  W , για τα μεσαία 100 W και για το τουίτερ  100 W.Ο ήχος του είναι απλά μαγικός και όλη η τεχνογνωσία και το ταλέντο των τεχνικών της Focal οδήγησαν σε αυτό το ηχείο νέας γενιάς.Με το SM9 οι πιο μικρές διαφορές στο compression ακούγονται μεγενθυμένα και με τρόπο που τα περισσότερα ηχεία δεν είναι ικανά να αποκαλύψουν.Ταυτόχρονα μια νέα πατέντα της Focal επιτρέπει το ηχείο απο σχεδίαση 3 δρόμων να μετατρέπεται με ένα κουμπί ( Focus) σε ηχείο 2 δρόμων με απόκριση 90 Hz έως 20 kHz έτσι ώστε να προσομειώνει μικρότερα ηχεία αλλά και τον τρόπο με τον οποίο ακούν πολλές φορές στις μέρες μας οι ακροατές απο φορητά συστήματα, συστήματα computer  κλπ Η τιμή του προϊόντος αφορά τεμάχιο και όχι ζευγάριΧαρακτηριστικά:Frequency response : 3-way mode : 30Hz - 40kHz (+/- 3dB) / 40Hz - 20kHz (+/- 1dB) - 2-way mode (Focus) : 90Hz - 20kHz (+/- 3dB)Maximum SPL : 3-way mode : 116dB SPL (peak @ 1m) / 2-way mode (Focus) : 106dB SPL (peak @ 1m)Input : Type / Impedance : Electronically balanced / 10 kOhms / Connector : XLR / Sensitivity : Adjustable, +4dBu or -10dBVBass : 400W, class ABMidrange- : 100W, class ABTreble : 100W, class ABPower supplies : Local supply : 230V (3.15A fuse), 115V (6.3A) - Connection: IEC inlet and detachable power cordIndicators :Rear panelInput sensitivity selector (+4dBu / -10dBV)High-pass crossover (full range, 45, 60, 90Hz @ -6dB)Low frequency shelving(+/- 3dB from 30 to 250Hz per step of 0.5dB)High frequency shelving(+/- 3dB from 4.5 to 40kHz per step of 0.5dB)Low frequency EQ(+/- 3dB per step of 0.5dB @ 50Hz, Q factor = 2)Low-mid frequency EQ(+/- 3dB per step of 0.5dB @ 160Hz, Q factor = 1)Mid frequency EQ(+/- 3dB per step of 0.5dB @ 1kHz, Q factor = 0.6)Side panelStand By / On switchDirect switchFocus switchwarning light : Power On, clipping and default on front panel LEDPassive radiator : 11WPP52, 11” (27cm) Focal “W” composite sandwich cone piston, extra wide inverted surround radiatorSubwoofer: 8W7571, 8” (20cm) Focal “W” composite sandwich cone driverMidrange : 6W0452, 6.5” (16.5cm) Focal “W” composite sandwich cone driverTweeter : TB872, 1” pure Beryllium inverted dome tweeterConstruction : 0.88”(22mm) and 1.2” (30mm) panels with internal bracesFinish : Black natural veneering top and bottom panels, black bodyDimensions : 12.8” x 19.6” x 15.6” (320mm x 490mm x 390mm)Net weight : 77lb (35kg) 

Integrated Amplifier with DAC, DSD, Phono, Airplay, Bluetooth and LAN !M-One is not only an integrated amplifier, but a window into a unique musical experience …No single audio product before the M-One delivers such a feature-packed and modern product that fits into such a small and elegant space – crafted from a single block of Aluminum.Essentially, it's an integrated amplifier, but with every connection you could want. Against all the odds, our engineers have managed to incorporate all the latest connections – Bluetooth aptX, LAN-Network 24bit /384kHz Asynchronous, SPDIF Coax-Opto-AES 24bit / 768kHz USB asynchronous passing DXD, DSD, DOP…, Phono MM / MC, Analog balanced and unbalanced inputs, and DSP with automatic room correction. Analog Balanced and Unbalanced Inputs, are just some of the inclusions.It is often the most demanding constraints that inspire engineers and designers to strive for creative and innovative solutions. Our tailor made M-One integrated amplifiers are a perfect example (M.C.F.) !Good Things Come in Small PackagesGet iOS App >Get Android App >Common audio wisdom dictates that high fidelity is best achieved with separate components, discreet circuitry, and space-consuming electronics and cables. However, this conventional wisdom is not without exception. Seeming contradictions exist where products have been able to produce the same phenomenal sound in a much smaller electronic package.This appears to be the logic behind the brand Micromega, whose paradoxical name has been associated with high-quality audio in unique packages since 1987. The company’s new M-One range of integrated amplifiers lives up to this legacy, offering a sleek and compact visual with a shocking array of connectivity options. It should go without saying that sound quality is at the forefront of the design. The device includes a DAC that is compatible with all high-resolution audio formats, a phono stage for turntables with both moving-magnet and moving-coil cartridges, power amplifier for loudspeakers, and many other options.The rear panel of the device has 26 connections, what one would expect from a mainstream A/V receiver rather than an audiophile integrated amplifier. Micromega touts that the device is encased in a cabinet milled from a single block of aluminum, and it comes in a variety of colors to suit the listener’s preferences. The M-One is sure to satisfy even the pickiest room designer or audiophile.It’s an absolute engineering miracle!Since your listening room is the weakest link in your installation, our engineers designed the M.A.R.S system to address this issue.This acoustic correction system and its Room EQ program detect the sound irregularities of your room and attenuate them for a balanced and accurate response. Over time, the dedicated application will provide this scalable system with a variety of additional features* MARS is included with M-150, in option with M-100* Premium Gloss finishes available for an additional $1000.00AMPLIFIER - classe AB* DAC PCM 32/768 et DSD256* DLNA* Ethernet* Bluetooth SBC - apt-X* S/PDIF - I2S* USB asynchronous* Calibration microphone M.A.R.S (optional)* Phono : MM / MC* 1.4 Vrms (RCA) - 1.7 Vrms (XLR)* 1x USB type B* 2x USB type A (service)* 2x HDMI I2S* 1x S/PDIF optique Toslink* 1x S/PDIF coaxiale RCA* 1x trigger* 1x INPUT XLR* 1x INPUT RCA* 1x phono MM/MC* 1x microphone* 1x pre-out XLR* 1x RCA* 1X SUB OUT* POWER : 2x100 W (8 Ohms) et 2x200 W (4 Ohms)* Rapport signal /bruit : 100 dB (RCA), 103 dB (XLR) et > 75 dB (phono)* SEPARATION: 96 dB @ 1 kHz et 80 dB @ 10 kHz430 x 56 x 350 mm10.7 kg         

Με εγγύηση μέχρι τον Μάϊο του 2022 με το κουτί του. Το Q 3090i χρησιμοποιεί τη νέα τεχνολογία P2P, το οποίο χρησιμοποιείται σε όλη τη σειρά 3000i, υποστηρίζει επιπλέον τα μέρη . Αυτό βελτιώνει την  αναπαραγωγή, μειώνει σημαντικά τους ανεπιθύμητους κραδασμούς. Το Q 3090i είναι ένα συμπαγές κέντρο, με σχεδιασμό διπλής ζώνης εξοπλισμένο με δύο μετατροπείς μπάσων 100mm.  Ενα συστήμα ανάρτησης το οποίο φιλτράρει τους κραδασμούς από τα μεγάφωνα μπάσων που επηρεάζουν αρνητικά την αναπαραγωγή και έτσι μειώνουν την απόδοση. Ο κώνος ακριβείας των υψηλών είναι κατασκευασμένος από εμποτισμένο χαρτί με επικάλυψη. Ο εμποτισμένος κώνος διασφαλίζει τη βέλτιστη ισορροπία μεταξύ της ακαμψίας και αυτο-απόσβεσης, το οποίο σημαίνει ότι μπορεί με ευελιξία και με ακρίβεια να ανταποκριθεί στις λεπτές παρορμήσεις χωρίς ανεπιθύμητους συντονισμούς. Το Textile μαγνητικό πλέγμα τονίζουν τη καθαριότητα. Οι ακροδέκτες ηχείου, καθώς και το πίσω μέρος του ηχείου με βύσματα μπανάνας δεχονται  και γυμνούς αγωγούς σε μία διάμετρο των 4 mm. Το  μοντέρνο σχέδιο, κάνει ελκυστικό το ηχείο και θα ταιριάζει σχεδόν σε οποιοδήποτε εσωτερικό χώρο. Το φινίρισμα επιφανειών γίνεται σε πρακτικό ματ φινίρισμα

The XPS is a simple and effective upgrade to enhance the music-making ability of your Naim Audio source component. As one of our most flexible performers it can be used to upgrade our CDX2 CD player and DAC digital to analogue converter, and it is also suitable for use with our NDS, NDX and ND5 XS network players and HDX hard-disk player/server. Its large toroidal transformer features four separate windings, coupled to six low-noise regulators and benefits from Naim Audio DR voltage regulator technology Features: Four isolated transformer windings with six low-noise DR power regulators - configured as two isolated regulators for digital at +15V, isolated +/-10V for DACs and isolated +/-23V for analogue stages All-new Discrete Regulator (DR) configuration, delivering Naim Audio’s best-ever standards of stable, low-noise power Brushed, black-anodised aluminium chassis plus anti-vibration feet Technology & Craft The Naim Audio XPS is a highly sophisticated power supply with six separately regulated, very low noise outputs, featuring a toroidal transformer and six power regulators. These supplies are branched and re-regulated, some twice in the CD player. The addition of anti-vibration, resonance-controlling feet complement the elegant cast and extruded anti-magnetic chassis protect the sensitive internal components from resonance and microphonic vibration. The XPS was updated in 2012 as a result of a two year project to develop a new discrete regulator (DR) for Naim Audio power supplies. The new Naim Audio DR now features, alongside improvements to the mechanical decoupling and internal layout. These enhancements, developed through intensive listening tests, significantly raise performance and make music even more communicative and enjoyable. Please note  Only new classic series XPS units are compatible with the NDX network player, not ‘Olive’ versions. The old ‘Olive’ XPS is still compatible with CDX and CDS model CD players, the HDX hard disk player and the DAC digital to analogue converter however. Please consult your Naim Audio retailer if you are unsure of compatibility. Finish: Case: Black powder coated Front: Brushed and black anodised Outputs: Power Outputs: ± 22V, ± 10V, 2 x 15V Physical: Shipping Weight: 15.1 kg Shipping Dimensions: 240 x 590 x 500mm Weight: 12.4 kg Dimensions (HxWxD): 87 x 432 x 314mm Power: Mains Supply: 100V, 115V, 230V; 50 or 60Hz Supplied with: Supplied with: Burndy Upgrades: Other: Power-Line Lite mains cable (UK denominations only)

This preamplifier is the center of your high-end stereo system as well as your multi-channel equipment. It guarantees sonic perfection for stereo playback lovers as well as the friends of multimedia experiences. A preamplifier which combines the exacting demands of a top class high-end stereo preamplifier with the connection and control range of a multimedia device for the first time. All this combined in a stunning and perfectly crafted technical work of art called: No.22 Cineast The input control takes place on the decibel precisely over the two existing multi-function switches for programming and setup, in typical AARON design. The twisted cone of solid material and the blue power indicator are embedded in the 10 mm thick aluminum front.You can control playback for 8 devices, such as a CD player, tuner, DVD, multi-channel equipment and a recording device, in the ideal manner with this preamplifier. Including the 2, a total of 6 output channels are available for mandatory outputs for high-end stereo playback. Our AARON sales representatives will happily inform you of the functions and uses that are ideal for you in stereo, bi-amping or even multi-channel operation.

Description: Three-way, floorstanding loudspeaker with treble and midrange horns, integral powered sealed-box woofer. Drive-units: inverted-dome tweeter loaded with 5.1"-diameter (130mm) horn, dome midrange driver loaded with 19.7"-diameter (500mm) horn, two 10" (250mm) cone woofers. Crossover frequencies: 300Hz, 3kHz. Frequency range: 300Hz–20kHz (midrange/treble), 18–300Hz (woofer). Sensitivity: >104dB. Nominal impedance: 8 ohms. Recommended power: >10W. Power handling: 50W. Subwoofer amplifier power: 250W.Dimensions: (including subwoofer) 50" (1270mm) H by 19.7" (500mm) W by 25.5" (520mm) D. Weight: 157 lbs (68kg).Finishes: Horns: Red, Blue, Silver, Black Pearlescent White (all metallic lacquers); other options available at additional cost. Subwoofer: Nextel Black.Read more at https://www.stereophile.com/content/avantgarde-acoustic-uno-nano-loudspeaker-specifications#Vt0E6mptifqgtzSm.99 Frequency Response: 22Hz to 20kHz Power Handling: 100W  Recommended Amplifier: 10W (minimum) Crossover Frequency: 170, 2000Hz  Impedance: 8Ω  Sensitivity: 101dB  Midbass: 1 x horn Tweeter: 1 x horn Dimensions: 670 x 680 x 1700mm Weight: 40kg

Το Focal Aria 926 ενσαρκώνει απόλυτα το ηχείο δαπέδου 3 δρόμων. Αυτό το μουσικό και εκφραστικό ηχείο είναι πολύ εύκολο στην συναρμολόγηση και εντυπωσιάζει όλους τους λάτρεις της μουσικής με τα ακουστικά του χαρακτηριστικά. Eίναι καθ’ορισμού ένα οικονομικό ηχείο για όλους τους λάτρεις της υψηλής απόδοσης ήχου.Ιδανικό για δωμάτια μετρώντας από 20m2 και για απόσταση ακρόασης των 3m ΧαρακτηριστικάΗχεία βάσης/βιβλιοθήκης 3 δρόμωνΝέο Flax Sandwich Cone της FocalΝέο TNF Tweeter της FocalΕγγύηση: 2 χρόνιαΗχεία σχεδιασμένα, ανεπτυγμένα και παρασκευασμένα στην Γαλλία.Επένδυση απο High Gloss και δέρμα. 

JBL JRX 225. Ηχείο 2 δρόμων, 1000W/Program, 4Ω, με woofer 2x15'' και driver 1'', διασπορά 90x50, 45Hz-12kHz, 100dBSPL/1W/1m. Προστασία υπεροδήγησης sonicguard, καμπίνα MDF, speakon και 1/4 jack. Διαστάσεις 1099Hx464Wx432Dmm. Βάρος 42,6kg. Χαρακτηριστικά:Power Rating500 / 2,000 WFrequency RangeAt -10 dB : 36 Hz to 19 kHzFrequency ResponseAt ±3 dB : 45 Hz to 16 kHzSensitivity100 dB SPL (1 W / 1 m) (1m)Nominal Impedance4 ΩAmplifier Power500 to 1000 W into 4 ΩMaximum SPL133 dBNominalDispersion: 90 x 50ºCrossover Frequency2 kHzHigh Frequency DriverJBL 2414H-C 1" (25 mm) polymer diaphragm compression driver mounted on Progressive Transition WaveguideLow Frequency Driver2 x JBL M128Input Connectors1 x Neutrik Speakon NL-4; 0.25" (6.35 mm)1 x TS phone jack; parallelDimensions (H x W x D)43.0 x 18.3 x 16.8" (1,092.0 x 464.0 x 426.0 mm)Weight94 lb (42.6 kg)