. go to top icon

Βραχίονες Πικάπ

Φίλτρα
17  Προϊόντα

An internally damped precision tonearm of highly polished stainless steel provides sparkling uncoloured reproduction offering pivot-stylus dimensions covering virtually all turntable requirements. The M2 Series tonearm is available in 9, 10 & 12 inch versions and offers at reasonable cost, meticulous build quality with all the most important features including lightweight stainless steel tonearm, detachable magnesium headshell with azimuth adjustment, tungsten balance weight, superb quality ball race bearings and a level of stiffness and rigidity to suit all types of cartridge. These precision made tonearms embody well tried SME principles and are suited to a broad range of cartridges including those of medium and low compliance. The headshell is pressure die-cast in magnesium for lightness and rigidity. A collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tighteningBuildThe M2-9 shell is pressure die-cast in magnesium for lightness and rigidity. Series M2-9 is the standard arm having a pivot-stylus dimension of 233.2 mm (9.18”) and will therefore be the one most frequently used. Series M2-10 is identical except that the pivot-stylus dimension is 239.3 mm (9.42”) a difference that suits the layout of some decks. Series M2-12 has a pivot-stylus dimension of 308.8 mm (12.16”). Distortion caused by lateral tracking error is at least 25% less than possible with a nine or inch arm. However effective mass will be typically 12.0 grams. Also, a turntable designed for 12-inch arms must be selected.DampingThe internally damped tonearm of highly polished stainless steel provides sparkling uncoloured reproduction. A unique single element balance system caters for cartridges weighing 5 to 12 grams. After balancing tracking force is applied by forward movement of the weight ensuring the lowest system inertia. The weight moves on a precision screw thread with backlash eliminator allowing exact setting of vertical tracking force.AdjustmentsA collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tightening. 1.0 gram per revolution tungsten weight sub-graduated 0.25 and 0.025 gram moving on a precision screw with backlash eliminator.
220mm (48”) D501 balanced audio lead. Engineered in the best camera quality with satin chrome finish Fluid damped lift/lower control.
Low friction, fully shielded races for both axes.
Sliding base for tracking adjustment.
Thumbwheel height adjustment.
Traditional pattern anti-skate. 

2.750 €
24 Άτοκες Δόσεις 114,58€ / μήνα
Κατόπιν Παραγγελίας

As a member of the M2 family this tonearm is built by enthusiasts for enthusiasts and among its extensive features include, vertical and horizontal tracking adjustment, tungsten balance weights housed in satin chromed brass sleeves. Double draw-pin detachable headshell with azimuth adjustment and height adjustment by thumb wheel enabling its use with wide range of both cartridges and turntables.BuildS2-R Aluminium shell detachable and interchangeable without disturbing cartridge or wiring. Double draw-in pin bayonet fitting design ensures a rigid junction with the tone-arm. Stainless steel ground horizontal spindle carried in substantial yoke in lOmm diameter precision ball race bearings. Stainless steel ground vertical spindle with integral 16mm diameter flange to couple the spindle with the yoke. The 23mm diameter steel pillar is heat treated, ground, internally honed and carries two 17mm diameter precision ball race bearings widely spaced to resist tilt. Internal wiring is Silver Litz.DampingInternal constrained layer damps minute residual vibrations making the tone-arm acoustically inert.AdjustmentsUnique headshell to tone-arm coupling readily allows cartridge azimuth adjustment. The Anti-Skate control operates through an Anti-Skate weight and filament and is adjustable for up to 5g of cartridge vertical tracking force (VTF). The lowering/raising control gives a smooth positive action and allows for the lifting height of the cartridge above the record to be adjusted. Tungsten-alloy balance weight inserts allow for maximum centre of gravity shift to balance a greater range of cartridges. Up to 38g in S2-R headshell and direct plug-in heads up to 46g. Precise vertical tracking force up to 5g is applied in 0.5 increments via the rider weight and graduated wayrod. Thumbwheel cartridge vertical tracking angle (VTA), height adjustment. Bedplate affords +/- 12.0mm movement to facilitate horizontal tracking angle (HTA) adjustment.

3.550 €
Άτοκες Δόσεις 1.183,33€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας Static 9'' Resonance optimaizedΠροδιαγραφές: Effective mass without headshell 3.5 gMass of supplied headshell 15.5 gEffective armlength (distance between the stylus and pivot point): 231.0 mmMounting distance (distance between the pivot point and turntable center): 213.0 mmOffset angle: 23.9 degreesOverhang: 18.0 mmTracking force adjusting range (direct reading): 0-3 gHeight adjustment range: 35-55 mmDiameter of the armbase mounting hole: 19-20 mmDiameter of the center shaft of tonearm: 18.0 mmInner null point: 66 mmOuter null point: 120.9 mmCounterweight for cartridge + headshell mass between 21 and 28 g includedHeadshell LH-2000E included Headshell LH-2000E weight: 15.5 gTA-110 total weight including headshell: 470 gSet of tonearm cables 6NX-TSW-1010 includedExtra mass ring for heavier cartridges included 

1.499 €
36 Δόσεις 51,75€ / μήνα
Κατόπιν Παραγγελίας

Precision tonearm with carbon-fibre armtube. The tonearm’s design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing. The tonearm fits on turntables or tonearm boards with mounting hole according to Linn standardFeaturesThe headshell and armtube are fashioned from a single piece of carbon-fibre.Conical armtube avoids standing wave reflections.Inverted bearing design with four ABEC7 spec ballraces.Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.Sorbothane® -damped counterweight effectively counteracts unwanted resonances.Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records.Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.Straight armtube reduces toe-in error.Silicone-damped armlift can be adjusted to suit arm height.The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated phono sockets.Terminal with phono sockets and earth screw.

845 €
36 Δόσεις 29,17€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας ευθύγραμμου τύπου Made in England. Ενεργό μήκος 9’’, Μοναδική χυτοπρεσαριστή κατασκευή εξ’ ολοκλήρου από αλουμίνιο. Μονοκόμματο μπράτσο με ειδική σκλήρυνση .Έδραση και κίνηση όλων των μερών με ρουλεμάν ακριβείας .Κατανομή μάζας μεγάλης ακριβείας.

649 €
36 Δόσεις 22,41€ / μήνα
Κατόπιν Παραγγελίας

The Nostatic Arm is the modern version of the formerly well known “Dust Bug” by Cecil   Watts. The Nostatic arm incorporates a carbon fiber brush that removes the static electricity from the record during playback, and at the same time picks up the loose dust before the stylus reaches that part of the record. The Nostatic arm has an earth wire which is connected to the earth of the record player or the amplifier. The height can be easily adjusted to fit most record players. It also has a sliding weight in order to adjust the “dusting force” of the brush. Finally the base of the brush has sticky tape so if preferred it can be stuck to the surface of the record player for easy use.

26 €
36 Δόσεις 0,90€ / μήνα
Κατόπιν Παραγγελίας

ΠεριγραφήΒραχίονας ευθύγραμμου τύπου με μονοκόμματο shell.

1.100 €
36 Δόσεις 37,98€ / μήνα
Κατόπιν Παραγγελίας

ΠεριγραφήΒραχίονας ευθύγραμμου τύπου με μονοκόμματο shell.

1.100 €
36 Δόσεις 37,98€ / μήνα
Κατόπιν Παραγγελίας

As a member of the M2 family this tonearm is built by enthusiasts for enthusiasts and among its extensive features include, vertical and horizontal tracking adjustment, tungsten balance weights housed in satin chromed brass sleeves. Double draw-pin detachable headshell with azimuth adjustment and height adjustment by thumb wheel enabling its use with wide range of both cartridges and turntables.BuildS2-R Aluminium shell detachable and interchangeable without disturbing cartridge or wiring. Double draw-in pin bayonet fitting design ensures a rigid junction with the tone-arm. Stainless steel ground horizontal spindle carried in substantial yoke in lOmm diameter precision ball race bearings. Stainless steel ground vertical spindle with integral 16mm diameter flange to couple the spindle with the yoke. The 23mm diameter steel pillar is heat treated, ground, internally honed and carries two 17mm diameter precision ball race bearings widely spaced to resist tilt. Internal wiring is Silver Litz.DampingInternal constrained layer damps minute residual vibrations making the tone-arm acoustically inert.AdjustmentsUnique headshell to tone-arm coupling readily allows cartridge azimuth adjustment. The Anti-Skate control operates through an Anti-Skate weight and filament and is adjustable for up to 5g of cartridge vertical tracking force (VTF). The lowering/raising control gives a smooth positive action and allows for the lifting height of the cartridge above the record to be adjusted. Tungsten-alloy balance weight inserts allow for maximum centre of gravity shift to balance a greater range of cartridges. Up to 38g in S2-R headshell and direct plug-in heads up to 46g. Precise vertical tracking force up to 5g is applied in 0.5 increments via the rider weight and graduated wayrod. Thumbwheel cartridge vertical tracking angle (VTA), height adjustment. Bedplate affords +/- 12.0mm movement to facilitate horizontal tracking angle (HTA) adjustment.

3.950 €
Άτοκες Δόσεις 1.316,67€ / μήνα
Κατόπιν Παραγγελίας

An internally damped precision tonearm of highly polished stainless steel provides sparkling uncoloured reproduction offering pivot-stylus dimensions covering virtually all turntable requirements. The M2 Series tonearm is available in 9, 10 & 12 inch versions and offers at reasonable cost, meticulous build quality with all the most important features including lightweight stainless steel tonearm, detachable magnesium headshell with azimuth adjustment, tungsten balance weight, superb quality ball race bearings and a level of stiffness and rigidity to suit all types of cartridge. These precision made tonearms embody well tried SME principles and are suited to a broad range of cartridges including those of medium and low compliance. The headshell is pressure die-cast in magnesium for lightness and rigidity. A collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tighteningBuildThe M2-9 shell is pressure die-cast in magnesium for lightness and rigidity. Series M2-9 is the standard arm having a pivot-stylus dimension of 233.2 mm (9.18”) and will therefore be the one most frequently used. Series M2-10 is identical except that the pivot-stylus dimension is 239.3 mm (9.42”) a difference that suits the layout of some decks. Series M2-12 has a pivot-stylus dimension of 308.8 mm (12.16”). Distortion caused by lateral tracking error is at least 25% less than possible with a nine or inch arm. However effective mass will be typically 12.0 grams. Also, a turntable designed for 12-inch arms must be selected.DampingThe internally damped tonearm of highly polished stainless steel provides sparkling uncoloured reproduction. A unique single element balance system caters for cartridges weighing 5 to 12 grams. After balancing tracking force is applied by forward movement of the weight ensuring the lowest system inertia. The weight moves on a precision screw thread with backlash eliminator allowing exact setting of vertical tracking force.AdjustmentsA collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tightening. 1.0 gram per revolution tungsten weight sub-graduated 0.25 and 0.025 gram moving on a precision screw with backlash eliminator.
220mm (48”) D501 balanced audio lead. Engineered in the best camera quality with satin chrome finish Fluid damped lift/lower control.
Low friction, fully shielded races for both axes.
Sliding base for tracking adjustment.
Thumbwheel height adjustment.
Traditional pattern anti-skate. 

2.950 €
24 Άτοκες Δόσεις 122,92€ / μήνα
Κατόπιν Παραγγελίας

Precision tonearm with carbon-fibre armtube. The tonearm’s design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing. The tonearm fits on turntables or tonearm boards with mounting hole according to Linn standardFeaturesThe headshell and armtube are fashioned from a single piece of carbon-fibre.Conical armtube avoids standing wave reflections.Inverted bearing design with four ABEC7 spec ballraces.Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.Sorbothane® -damped counterweight effectively counteracts unwanted resonances.Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records.Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.Straight armtube reduces toe-in error.Silicone-damped armlift can be adjusted to suit arm height.The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated phono sockets.Terminal with phono sockets and earth screw.

845 €
36 Δόσεις 29,17€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας ευθύγραμμου τύπου Made in EnglandΕνεργό μήκος 9’’Μοναδική χυτοπρεσαριστή κατασκευή εξ’ ολοκλήρου από κράμα αλουμινίουΜονοκόμματο μπράτσο με ειδική σκλήρυνση, θερμική βαφή και κατεργασία στο χέριΈδραση και κίνηση όλων των μερών με ρουλεμάν υψηλής ακριβείας μηδενικών ανοχών κατασκευασμένων από χρωμονικελιούχο χάλυβαΤα ρουλεμάν έδρασης επιλέγονται αυστηρά ανά ταιριασμένο ζεύγος για κάθε βραχίοναΠλήρη κατανομή μάζας με υψηλή ακρίβεια και ισορροπία

2.099 €
36 Δόσεις 72,46€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας ευθύγραμμου τύπου Made in EnglandΜοναδική χυτοπρεσαριστή κατασκευή εξ’ ολοκλήρου από αλουμίνιοΜονοκόμματο μπράτσο με ειδική σκλήρυνση και θερμική βαφήΈδραση και κίνηση όλων των μερών με ρουλεμάν ακριβείαςΚατανομή μάζας μεγάλης ακριβείας

1.099 €
36 Δόσεις 37,94€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας ευθύγραμμου τύπου Ενεργό μήκος 9’’. Ο RB202 είναι η τελευταία ενσάρκωση ενός από τους πιο δημοφιλείς tonearms,του πρότυπου RB250. Το πιο πρόσφατο σχέδιο εκμεταλλεύεται πλήρως τον ολοκαίνουργιο χειροποίητο σωλήνα και το νεότερο σύστημα ανάρτησης τριών σημείων. Κάθε RB202 είναι συναρμολογημένα στο χέρι, δημιουργώντας μια ακρίβεια κατασκευής βραχίονα με επίτευξη εξαιρετικά χαμηλά επίπεδα τριβής και απόδοση πέρα από τις προσδοκίες ενός προϊόντος σε αυτή τη κατηγορία τιμής.Χαρακτηριστικά:Βραχίονας ευθύγραμμου τύπουΕνεργό μήκος 9’’Χειροποίητης κατασκευής από ειδικό κράμα αλουμινίουΈδραση και κίνηση όλων των μερών με ρουλεμάνΚατανομή μάζας μεγάλης ακριβείαςΡύθμιση anti-skatingΣτήριξη βάσης τριών σημείων 

229 €
36 Δόσεις 7,91€ / μήνα
Άμεσα Διαθέσιμο

Βραχίονας Static 12'' Resonance optimaizedΠροδιαγραφές:  Effective mass without headshell: 5 gEffective armlength (distance between the stylus and pivot point): 329.0 mmMounting distance (distance between the pivot point and turntable center): 316.6 mmOffset angle: 16.5 degreesOverhang: 12.4 mmTracking force adjusting range (direct reading): 0-3/0-4 gHeight adjustment range: 35-55 mmDiameter of the armbase mounting hole: 19-20 mmDiameter of the center shaft of tonearm: 18.0 mmInner null point: 66 mmOuter null point: 120.9 mmCounterweight for cartridge + headshell mass between 21 and 28g includedHeadshell LH-2000E included Headshell weight: 15.5 gTA-210 total weight including headshell: 536 gSet of tonearm cables 6NX-TSW-1010 includedExtra mass ring for heavier cartridges included

1.549 €
36 Δόσεις 53,48€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας Static 12''Προδιαγραφές:  Effective length (distance between the stylus and pivot point): 329mmMounting distance between the pivot point and turntable center: 314mmOffset angle: 19 degreesOverhang: 15mmTracking force adjusting range ( direct reading): 0 to 3gHeight adjustment range: 35mm to 55mmDiameter of the armbase mounting hole: 19mm to 20mmDiameter of center shaft: 18mm

1.899 €
36 Δόσεις 65,56€ / μήνα
Κατόπιν Παραγγελίας

Βραχίονας Dynamic 12''Προδιαγραφές: Effective length (distance between the stylus and pivot point): 329mmMounting distance between the pivot point and turntable center: 314mmOffset angle: 19 degreesOverhang: 15mmTracking force adjusting range (direct reading): 0 - 5 g Height adjustment range: 42 mm - 57 mmDiameter of  the armbase mounting hole: 34 mm - 36 mmDiameter of the center shaft: 16 mmFixing holes PCD: dia. 50 mmSize/Thread: dia. 3.2 mm (dia. 3mm x 20mm and dia. 3 mm wood screw)Digital scale DS 1 includedHeadshell SH-1 included

2.699 €
36 Δόσεις 93,18€ / μήνα
Κατόπιν Παραγγελίας