go to top icon

Τελικοί Ενισχυτές

Φίλτρα
87  Προϊόντα
Σελ
από 2

RB-1552 MkII is built upon the same platform as the RB-1582 MkII with only a slightly smaller power output capability at 2 x 130 Watts. The RB-1552 MkII is a 130 Watt per channel class AB amplifier. It is engineered to be powerful and robust, yet able to extract every last nuance out of even the most complex musical score.  Notable features of the amplifier include independent left and right power rectification stages and decoupling. The layout is essentially a mono block design. Further evidence of design over-spec is in the selection of premium “slit-foil” capacitors, which provide plenty of reserve energy for extremely dynamic audio passages and are able to quickly replenish themselves due to the nature of their unique design. Input options are balanced XLR or unbalanced RCA connectors. The RB-1552 MkII stereo amplifier has been engineered to provide high-resolution audio performance, yet it is very affordable, as has been the tradition with Rotel electronics for over 50 years.

880 €
36 Δόσεις 30,38€ / μήνα
Κατόπιν Παραγγελίας

RB-1552 MkII is built upon the same platform as the RB-1582 MkII with only a slightly smaller power output capability at 2 x 130 Watts. The RB-1552 MkII is a 130 Watt per channel class AB amplifier. It is engineered to be powerful and robust, yet able to extract every last nuance out of even the most complex musical score.  Notable features of the amplifier include independent left and right power rectification stages and decoupling. The layout is essentially a mono block design. Further evidence of design over-spec is in the selection of premium “slit-foil” capacitors, which provide plenty of reserve energy for extremely dynamic audio passages and are able to quickly replenish themselves due to the nature of their unique design. Input options are balanced XLR or unbalanced RCA connectors. The RB-1552 MkII stereo amplifier has been engineered to provide high-resolution audio performance, yet it is very affordable, as has been the tradition with Rotel electronics for over 50 years.

880 €
36 Δόσεις 30,38€ / μήνα
Κατόπιν Παραγγελίας

Featuring 6 x 50 watts per channel, the RMB-1506 is a rugged, sophisticated, multichannel amplifier for those with a limited number of zones to fill with music. The RMB-1506 is perfect for less elaborate multizone audio systems and can be mated with our surround receiver or our preamp/processors to add music throughout three additional living areas or “zones” of your home. A buffered link output allows you to link additional amplifiers for larger multizone applications. As with all Rotel custom amplifiers it includes the most wanted custom installation features such as front panel attenuation control, input linking, 12-volt trigger, buffered link output, five-way binding posts and an IEC detachable power cord.

970 €
36 Δόσεις 33,49€ / μήνα
Κατόπιν Παραγγελίας

Featuring 6 x 50 watts per channel, the RMB-1506 is a rugged, sophisticated, multichannel amplifier for those with a limited number of zones to fill with music. The RMB-1506 is perfect for less elaborate multizone audio systems and can be mated with our surround receiver or our preamp/processors to add music throughout three additional living areas or “zones” of your home. A buffered link output allows you to link additional amplifiers for larger multizone applications. As with all Rotel custom amplifiers it includes the most wanted custom installation features such as front panel attenuation control, input linking, 12-volt trigger, buffered link output, five-way binding posts and an IEC detachable power cord.

970 €
36 Δόσεις 33,49€ / μήνα
Κατόπιν Παραγγελίας

Music everywhere with 8 x 50 watts per channel is the purpose of our rack mountable RKB-850. Rotel has been designing and manufacturing award-winning power amplifiers for over 50 years. That considerable expertise has now been applied to a new generation of rackmount custom installation amplifiers that set new standards for performance, reliability, and ease of installation. The RKB-850 is rated at 8 x 50 Watts RMS into 8 ohms all channels driven, and can double that output into 4 ohms as a result of its sophisticated, efficient Class D design. The amplifier is rugged and extremely reliable, but Rotel has gone one step further to maximize long service life by utilizing dual thermostatically controlled fans to exhaust heat away from the output modules and power supply. One of the many custom-friendly features the RKB-850 offers is input linking. A second input can source from any ‘upstream’ input - so B can source from A, C can source from B and D can source from C. You can create four individual stereo zones, two dual zones or three common zones plus an individual zone. In other words, two Sonos Connects (for instance) might be divided between kitchen and patio (A+B zones) and Master Bedroom and Bath (C+D). Other features include input signal sensing, buffered link output, a sum-to-mono feature, a rear panel RS232 connection allowing connection to automation systems to provide full control and feedback, and four front panel trim pots to allow easy level adjustment to balance zones.

1.400 €
36 Δόσεις 48,33€ / μήνα
Κατόπιν Παραγγελίας

Τηλεχειριζόμενος προ-ενισχυτής, με διπλό τοροειδή μετασχηματιστή. DAC 32bit/768kHz, Θύρα RS-232, Bluetooth with aptX, 12V trigger, USB for Apple iOS devicesx

1.690 €
36 Δόσεις 58,34€ / μήνα
Κατόπιν Παραγγελίας

Τηλεχειριζόμενος προ-ενισχυτής, με διπλό τοροειδή μετασχηματιστή. DAC 32bit/768kHz, Θύρα RS-232, Bluetooth with aptX, 12V trigger, USB for Apple iOS devicesx

1.690 €
36 Δόσεις 58,34€ / μήνα
Κατόπιν Παραγγελίας

RMB-1512 is the ideal whole-house music amplifier with 12 x 100 Watts per channel. No longer do you need to purchase several large amplifiers to obtain a high performance multizone audio system. The RMB-1512 features an advanced Class D design that provides plenty of power (12 x 100 Watts into 8 ohms) for the most demanding multizone audio systems, but never runs the danger of overheating itself or other electronic components placed in the same vicinity. The RMB-1512 features everything needed for remote operation and custom installation including 12 volt trigger, signal sensing, input bussing, sum-to-mono, buffered link output, front panel attenuation controls, five-way binding posts and screw terminals.

2.500 €
36 Δόσεις 86,31€ / μήνα
Κατόπιν Παραγγελίας

P1 is a top of the range preamplifier. An audiophile model capable of sublimating all your music while maintaining an optimal signal-to-noise ratio and a distortion reduced to the strict minimum. The product is not fixed in time, its optional input cards and its modularity allow it to easily follow the market's evolutions. The MPH II and MDAC I modules are provided in the P1 FULL version. Equipped with line inputs in its original configuration, it can in fact be completed by optional slot cards: one for the Phono RIAA MM/MC stages, as well as another module offering three digital inputs with a resolution of up to 32 bits sampled at 384 kHz. This modularity, for both the analogue and digital parts, is supported by internal software that can be upgraded by the user via an easily accessible USB socket. Elipson P1 is thus a device of the present turned towards the future. Elegant and sober at the same time, the P1 is totally transparent thanks to the care taken with its circuits, allowing extremely low noise and distortion. Complete with multiple possibilities, its interface via the front screen offers you a perfect comfort of use, completed by its personalized and elegant remote control. The result is a reproduction of the smallest details, an airy spatialization and a perfect respect of silences. Our range is entirely manufactured in France in our Burgundy factory.

1.990 €
12 Άτοκες Δόσεις 165,83€ / μήνα
Κατόπιν Παραγγελίας

Achilles is a small monoblock class A triode amplifier with superior sound performance. It needs a sensitive speaker as a load but it will amaze you with its performance. A beautiful small size amplifier for many relaxing music hours.

3.900 €
36 Δόσεις 134,64€ / μήνα
Κατόπιν Παραγγελίας

Achilleas , Power Amplifier, 2 x 8 Watt,με 2 λυχνίες 300B / 2 x 2A3, 2 x 6SL7, 2 x 6L6).Ο Αχιλλέας είναι ένας μικρής κατηγορίας monoblock ενισχυτής με τρίοδο σχεδίαση σε τάξη Α, με κορυφαία απόδοση ήχου.Χρειάζεστε ένα ευαίσθητο ηχείο ως φορτίο, αλλά το αποτέλεσμα θα σας καταπλήξει με την απόδοσή του.Ένα όμορφος ενισχυτής μικρού μεγέθους για πολλές ώρες χαλάρωσης μουσική.

2.100 €
36 Δόσεις 72,50€ / μήνα
Κατόπιν Παραγγελίας

When musicality is all that matters Artemis is what you need. An amplifier with high sound performance that will give you hours of pleasant listening to your favorite music. Artemis is the only amplifier of this series that is not in monoblock construction. It is all in one chassis dual-mono construction. It is in class AB1 push pull configuration.

4.100 €
36 Δόσεις 141,55€ / μήνα
Κατόπιν Παραγγελίας

When musicality is all that matters Artemis is what you need. An amplifier with high sound performance that will give you hours of pleasant listening to your favorite music. Artemis is the only amplifier of this series that is not in monoblock construction. It is all in one chassis dual-mono construction. It is in class AB1 push pull configuration.

2.200 €
36 Δόσεις 75,95€ / μήνα
Κατόπιν Παραγγελίας

When musicality is all that matters Artemis is what you need. An amplifier with high sound performance that will give you hours of pleasant listening to your favorite music. Artemis is the only amplifier of this series that is not in monoblock construction. It is all in one chassis dual-mono construction. It is in class AB1 push pull configuration.

1.599 €
36 Δόσεις 55,20€ / μήνα
Κατόπιν Παραγγελίας

Ο Tsakiridis Devices Artemis είναι τελικός ενισχυτής (dual mono), ισχύος 2x35 έως 2χ70 wrms 8ohms, το στάδιο εξόδου υλοποιείται με 4x λυχνίες (EL34, 6550 ή KT150).

1.389 €
36 Δόσεις 47,95€ / μήνα
Κατόπιν Παραγγελίας

Apollon in Greek Mythology was the God of music. A fitting name for this amplifier as it has excellent sound. It carries almost 20 years of development, as it is the descendant of the very first amplifier our company put to trade. Then it was named Powerhouse but now it is Apollon, the God of music. It incorporates 4 power tubes per channel which form a dual push pull. They are biased in class AB1 class of operation. Powerful enough to drive difficult loads and give you a unique sonic experience.

6.200 €
36 Δόσεις 214,05€ / μήνα
Κατόπιν Παραγγελίας

Apollon in Greek Mythology was the God of music. A fitting name for this amplifier as it has excellent sound. It carries almost 20 years of development, as it is the descendant of the very first amplifier our company put to trade. Then it was named Powerhouse but now it is Apollon, the God of music. It incorporates 4 power tubes per channel which form a dual push pull. They are biased in class AB1 class of operation. Powerful enough to drive difficult loads and give you a unique sonic experience.

3.470 €
36 Δόσεις 119,80€ / μήνα
Κατόπιν Παραγγελίας

Appolon Plus, Power Amplifier, 2 x 90 Watt με (8 λυχνίες 6550 και 4 12AT7). Ο Απόλλων στην Ελληνική Μυθολογία ήταν ο Θεός της μουσικής. Ένα ταιριαστό όνομα για αυτόν τον ενισχυτή που έχει με αντικειμενική παραδοχή, εξαιρετικό ήχο. Μεταφέρει σχεδόν 20 χρόνια ανάπτυξης τεχνολογίας, όπως ο απόγονος, του πρώτου ενισχυτή της εταιρείας μας στο εμπόριο. Πήρε το όνομά του ως Powerhouse, αλλά ο νέος τώρα είναι Απόλλων, ο θεός της μουσικής. Ο Plus Ενσωματώνει 4 λυχνίες ισχύος ανά κανάλι, που σχηματίζουν διπλό “push pull”. Είναι πολωμένος σε κατηγορία τάξη ΑΒ1 λειτουργίας, αρκετά ισχυρός για να οδηγήσει δύσκολα φορτία και να σας δώσει μια μοναδική ηχητική εμπειρία.

2.799 €
36 Δόσεις 96,63€ / μήνα
Κατόπιν Παραγγελίας

Appollon, Power Amplifier, 2 x 70 Watt,με 8 λυχνίες EL 34 και 4 x 12AT7.  Ο Απόλλων στην Ελληνική Μυθολογία ήταν ο Θεός της μουσικής. Ένα ταιριαστό όνομα για αυτόν τον ενισχυτή που έχει με αντικειμενική παραδοχή, εξαιρετικό ήχο. Μεταφέρει σχεδόν 20 χρόνια ανάπτυξης τεχνολογίας, όπως ο απόγονος, του πρώτου ενισχυτή της εταιρείας μας στο εμπόριο. Πήρε το όνομά του ως Powerhouse, αλλά ο νέος τώρα είναι Απόλλων, ο θεός της μουσικής. Ενσωματώνει 4 λυχνίες ισχύος ανά κανάλι, που σχηματίζουν διπλό “push pull”. Είναι πολωμένο σε κατηγορία τάξης ΑΒ1 λειτουργίας, αρκετά ισχυρό για να οδηγήσει δύσκολα φορτία και να σας δώσει μια μοναδική ηχητική εμπειρία.

2.329 €
36 Δόσεις 80,41€ / μήνα
Κατόπιν Παραγγελίας

Το X-A220 προσφέρει ισχύ 220 W ανά κανάλι σε τάξη ΑΒ και  με ένα διακόπτη στην πίσω πλευρά επιτρέπει να δώσει τα πρώτα 45 W στην class Α και πέρα από αυτό το όριο, ο ενισχυτής αλλάζει αυτόματα σε Class AB. Η υψηλή παροχή ηλεκτρικού ρεύματος που συνδέονται με το στάδιο της τριπλής εξόδου που παρέχεται με τα "υψηλού επίπεδου Ρεύματος" τρανζίστορ του διάσημου ΜΑΑ 1000 (NJW0281G - NJW0302G), επιτρέπουν στον ενισχυτή μονο ισχύος X-A220 για να παραδώσει ισχύ  220 Watts RMS στα 8 Ohm. ωδές. Σε συνδυασμό με τη λειτουργία του "Hi Bias", ο X-A220 θα οδηγήσει εύκολα όλα τα ηχεία που υπάρχουν στην αγορά.

1.500 €
36 Δόσεις 51,79€ / μήνα
Κατόπιν Παραγγελίας

Το BX2 είναι ένας μονοφωνικός ενισχυτής ισχύος 210 Watts Ohms. Η ομάδα ανάπτυξης του Advance Paris έχει εμπνευστεί από τον ενισχυτή αναφοράς X-A1200 για τη δημιουργία του ενισχυτή BX2. Αυτός ο ενισχυτής μπορεί να οδηγήσει όλους τους τύπους ηχείων και είναι απόλυτα συμβατός για χρήση HiFi ή home-cinema. Το BX2 ενσωματώνει καλύτερα επιλεγμένα εξαρτήματα και ειδικά έχει γίνει προσπάθεια στο τμήμα τροφοδοσίας. Ο υπερμεγέθης δακτυλιοειδής μετασχηματιστής συνδυασμένος με πυκνωτές 10.000uF / 80V επιτρέπει στο BX2 να παρέχει υψηλό επίπεδο ρεύματος.

990 €
36 Δόσεις 34,18€ / μήνα
Κατόπιν Παραγγελίας

Το BX2 είναι ένας μονοφωνικός ενισχυτής ισχύος 210 Watts Ohms. Η ομάδα ανάπτυξης του Advance Paris έχει εμπνευστεί από τον ενισχυτή αναφοράς X-A1200 για τη δημιουργία του ενισχυτή BX2. Αυτός ο ενισχυτής μπορεί να οδηγήσει όλους τους τύπους ηχείων και είναι απόλυτα συμβατός για χρήση HiFi ή home-cinema. Το BX2 ενσωματώνει καλύτερα επιλεγμένα εξαρτήματα και ειδικά έχει γίνει προσπάθεια στο τμήμα τροφοδοσίας. Ο υπερμεγέθης δακτυλιοειδής μετασχηματιστής συνδυασμένος με πυκνωτές 10.000uF / 80V επιτρέπει στο BX2 να παρέχει υψηλό επίπεδο ρεύματος.

990 €
36 Δόσεις 34,18€ / μήνα
Κατόπιν Παραγγελίας

The BX1 is a stereo power amplifier that can be linked with AX1, DX1 or PX1. This amplifier 2*105 w on 8 Ohms will be able to drive, due to its versatility, neutrality and dynamics, most of the speakers found in the market.Thanks to its white or black transparent methacrylate front panel, you will appreciate its design and ergonomics, as the general conception and building of the several subsets inside. Our BX1 provides Cinch (unbalanced) or XLR ( balanced) connectors, switchable on the rear panel.BX1 has a High Bias function, that allows the amplifier to deliver the first watts in a similar A Class.After that, the amp will be working in Class AB. The inside tooling is based on compartments, insuring mecanical rigidity and the components shielding, starting with the 480 VA toroidal transformer. The voltage is rectified by 4 capacitors of 6800 uF under 63 volts.Power stages are supplied by Toshiba transistors that are famous for their audio quality.The result is a neutral and transparent listening, especially by an excellent performance in sound power. The lower frequencies are strengh and without heaviness, and for the medium frequencies, a very detail rendering of the voices and audio signal.The trebles are not left out with a lack of agressiveness and great finesse. The BX1 provides speaker connectors in order to connect 2 pairs of loudspeakers.

990 €
36 Δόσεις 34,18€ / μήνα
Κατόπιν Παραγγελίας

The BX1 is a stereo power amplifier that can be linked with AX1, DX1 or PX1. This amplifier 2*105 w on 8 Ohms will be able to drive, due to its versatility, neutrality and dynamics, most of the speakers found in the market.Thanks to its white or black transparent methacrylate front panel, you will appreciate its design and ergonomics, as the general conception and building of the several subsets inside. Our BX1 provides Cinch (unbalanced) or XLR ( balanced) connectors, switchable on the rear panel.BX1 has a High Bias function, that allows the amplifier to deliver the first watts in a similar A Class.After that, the amp will be working in Class AB. The inside tooling is based on compartments, insuring mecanical rigidity and the components shielding, starting with the 480 VA toroidal transformer. The voltage is rectified by 4 capacitors of 6800 uF under 63 volts.Power stages are supplied by Toshiba transistors that are famous for their audio quality.The result is a neutral and transparent listening, especially by an excellent performance in sound power. The lower frequencies are strengh and without heaviness, and for the medium frequencies, a very detail rendering of the voices and audio signal.The trebles are not left out with a lack of agressiveness and great finesse. The BX1 provides speaker connectors in order to connect 2 pairs of loudspeakers.

990 €
36 Δόσεις 34,18€ / μήνα
Κατόπιν Παραγγελίας

The Pre-XR is one of the first wave of products, heralding the new XR series of Cyrus components. The familiar Cyrus precision die-cast case is the same, but everything else has changed. With ground-up engineering inside, an all-new phantom black paint finish, touch-sensitive controls and a higher resolution display that is customisable for brightness, contrast and polarity, the high-quality finish of XR makes a strong statement. High Capacity Power Supply The power supply design of the Pre-XR has received special attention. An over-specified 74VA power transformer delivers power to a high capacity power supply reserve. Within the circuit design, a generous total of 15 independent power supply regulators regulate, then sub regulates quiet power. Digital control circuits are assigned a separate mains power supply, completely isolated from the signal circuitry. Balanced And Unbalanced Output Options  The Pre-XR features a choice of balanced audio drive via XLR connectors for best performance in systems where it is partnered by high-end power amplifiers with balanced inputs. An unbalanced output is also provided. All New Analogue Preamplifier The Pre-XR analogue preamp features relay input selection and a new high-performance gain stage. This short path design makes the analogue preamplifier extremely transparent. With four analogue inputs and phono MM, the Pre-XR will cover just about any system requirement for analogue connectivity. PSU-XR Port The Pre-XR includes a port for the new PSU-XR power supply. Thirty years ago Cyrus broke new ground with the introduction of the PSX-R, the first-ever regulated power supply upgrade that automatically adapted to match perfectly the power requirements of any connected product. The PSU-XR raises the bar by sourcing no less than five independent regulated supplies in a single box. For the Pre-XR the PSU-XR steps in to take over power supply for the analogue stages of the preamplifier. PRE-XR Digital Performance  The DAC input stage of the Pre-XR features a new 2nd generation version of our award-winning QXR DAC, but with an all-new high-speed analogue buffer stage. Seven digital filter alignment options are user adjustable to suit the taste of the listener. Input options include USB audio (to 768k sample rate) and DSD to DSD512, 2 x SPDIF digital and 2 x optical digital inputs. Fully Configurable  A new menu system makes the Pre-XR highly customisable yet easy to set up. With a tree-style navigation structure and both local and remote control navigation, menu settings are quick and simple to select.

4.765 €
36 Δόσεις 164,50€ / μήνα
Κατόπιν Παραγγελίας

Exceptional Power, Immersive Sound The PA720 is a high-performance power amplifier that delivers 7 channels of efficient Class G amplification. With an impressive 140W per channel, the PA720 is designed to offer the greatest flexibility and power without compromising on control. Featuring the best-in-class components including a toroidal based power supply, acoustically damped chassis, paralleled transistor output stages and exceptionally low levels of distortion, the PA720 masters the reproduction of music with all its originality and detail for an unmatched level of sound quality and clarity.

3.410 €
36 Δόσεις 117,73€ / μήνα
Κατόπιν Παραγγελίας

Exceptional Power, Immersive Sound The PA410 is a high-performance power amplifier that delivers 4 channels of efficient Class AB amplification. With an impressive 70W per channel, the PA410 is designed to offer the greatest flexibility and power without compromising on control.  Featuring the best-in-class components including a toroidal based power supply, acoustically damped chassis, paralleled transistor output stages and exceptionally low levels of distortion, the PA410 masters the reproduction of music with all its originality and detail for an unmatched level of sound quality and clarity.

1.700 €
36 Δόσεις 58,69€ / μήνα
Κατόπιν Παραγγελίας

Ο σχεδιασμός της σειράς HDA βασίζεται σε όλη την εμπειρία της Arcam ως μία από τις πιο σεβαστές εταιρείες ήχου του Ηνωμένου Βασιλείου, για την παραγωγή της γκάμας ηχητικών προϊόντων με την καλύτερη απόδοση της Arcam - χρησιμοποιώντας τα καλύτερα ποιοτικά εξαρτήματα και τεχνικές πρακτικές, η σειρά HDA έχει σχεδιαστεί και κατασκευαστεί για σας δίνουν χρόνια απόλαυσης.

2.480 €
36 Δόσεις 85,62€ / μήνα
Κατόπιν Παραγγελίας

Amazing Flexibility The C 298 may be a basic Power Amp, but we have carefully thought through all the use cases typically encountered to create a rich feature content. Selectable balanced inputs make the C 298 a natural for studio use or connection to High End Preamps and Processors. These inputs include a trim control useful for matching to other components. A line out allows further addition of power on the same channel for additional speakers or subwoofers. Auto-sense with selectable threshold is perfect for automating complex systems or hiding the amp out of sight in a cabinet. We even include a Ground Lug that can be very useful for eliminating ground loops and noise in complex multi-unit systems. Added to all this connectivity is a Bridge Switch that turns the C 298 into an amazingly powerful Monobloc Amplifier. Start with one and add a second C 298 later when you upgrade your speakers. Getting the Basics Right It is surprising how many seemingly advanced products in the market today often miss many of the most basic requirements for satisfying performance. Low noise circuits, accurate channel balance, proper input and output impedance characteristics, high overload margins and stability with difficult speaker loads. NAD starts by getting these things precisely right and advances from there. Our line inputs, both Balanced and Single-ended, can accommodate all kinds of analog source components by offering ideal input impedance characteristics with linear ultra-low-noise buffer amplifiers to prevent any sonic degradation caused by inappropriate loading of the source device. These are all details you can hear. Sophisticated Power NAD has moved away from the old fashioned and very power hungry linear power supplies and Class AB output stages that waste nearly half of the energy consumed producing heat rather than sound. Instead we have developed even better performing circuits based on switch mode power supplies and Class D output stages. Once thought to be inferior to traditional topologies, NAD’s advanced work in this area has created some of the best performing amplifiers regardless of basic design principle. These new designs are very linear over a wide bandwidth and provide consistent performance into all speaker loads, providing a dramatic advance over previous models. The generously dimensioned power supply easily allows for 185 watts continuous and over 570 watts instantaneous power for short term musical transients. Innovative Asymmetrical Power-Drive fully utilizes every last watt available with its vast reserves of dynamic power available to accurately reproduce musical transients without distortion or compression. It can operate with any AC mains voltage from 100v to 240v and provides pure DC power to all the various stages of the C 298. This highly efficient supply also provides near perfect regulation of voltage across a wide range of conditions and provides a solid noise-free foundation for the amplifying stages. Purifi ‘Eigentakt’ Amplifier Technology Purifi is a Danish technology company that has brought together several of the industry’s leading engineers to apply advanced mathematical modelling to solve the last remaining limitations of audio amplifiers. While there are many good sounding amplifiers on the market today, Purifi has taken a fresh look at every aspect of amplifier performance and found many seemingly small non-linearities that can make a dramatic difference in the overall sound. This return to first principles has resulted in a stunningly simple approach to some remarkably complex problems. With features and technology unmatched by other amplifiers in its class, the C 298 amplifier is an easy upgrade for any system and a surprising partner for the most sophisticated and advanced loudspeakers on the market.

1.999 €
36 Δόσεις 69,01€ / μήνα
Κατόπιν Παραγγελίας

Τελικός Ενισχυτής Home cinema 7 Καναλιών Ισχύς 7X150 W.

2.299 €
36 Δόσεις 79,37€ / μήνα
Κατόπιν Παραγγελίας

Τελικός ενισχυτής Class D 2 x 250W.

1.080 €
36 Δόσεις 37,29€ / μήνα
Κατόπιν Παραγγελίας

Τελικός ενισχυτής Class D 2 x 250W.

1.080 €
36 Δόσεις 37,29€ / μήνα
Κατόπιν Παραγγελίας

Τελικός ενισχυτής Class AB 2 x 350W, με διπλό τοροειδή μετασχηματιστή.

2.900 €
36 Δόσεις 100,12€ / μήνα
Κατόπιν Παραγγελίας

Τελικός ενισχυτής Class AB 2 x 350W, με διπλό τοροειδή μετασχηματιστή.

2.900 €
36 Δόσεις 100,12€ / μήνα
Κατόπιν Παραγγελίας

THE QUIETEST, CLEANEST AUDIO AMPLIFIER ON THE PLANET From the first watt to the last watt, no audio power amplifier offers lower noise or lower distortion than the Benchmark AHB2.Benchmark has raised the bar by introducing a new and revolutionary amplifier! TRUE HIGH-RESOLUTION PERFORMANCE  The AHB2 is the ideal match to the performance limits of High-Resolution-Audio (HRA) formats. Benchmark's AHB2 power amplifier delivers musical details without introducing the masking effects of amplifier noise and distortion. The dynamic range of the AHB2 is 132 dB, making it 10 to 30 dB quieter than some of the very best reference-quality power amplifiers. The frequency response of the AHB2 extends beyond 200 kHz. With the AHB2, you will discover previously overlooked nuances, dynamics, and detail in your favorite recordings and experience the full potential of the latest high-resolution 24-bit PCM and 1-bit DSD audio formats. EXPERIENCE THE EMOTION The musical details and emotion captured on today's finest High-Resolution-Audio recordings can only be fully appreciated when every component in the signal chain is capable of true high-resolution performance. Power amplifiers are a weak link in most audio systems. Most power amplifiers are well matched to the limitations of the CD format, but they fall well short of the capabilities of high-resolution formats. In contrast, the revolutionary AHB2 was specifically designed to deliver true high-resolution performance. FULFILLING THE NEED FOR BETTER AMPLIFICATION D/A conversion technology has outpaced the development of new power amplifiers. This means that the power amplifier has become a limiting factor in many audio systems. For example, the noise and distortion produced by the Benchmark DAC3 D/A converter is 20 to 30 dB lower than that produced by most high-quality power amplifiers. Until now, this meant that the DAC3 could not be fully appreciated. Benchmark set out to solve this problem by creating an amplifier that matches the performance of the DAC3. A RADICALLY DIFFERENT POWER AMPLIFIER We had to look beyond existing amplifier technologies and explore some new and radical solutions. In our search, we learned of two new patents on a new amplifier technology from THX. This was exactly the technology we needed to build our new amplifier. The AHB2 uses the new and revolutionary THX-patented AAA™ technology to virtually eliminate all forms of distortion. This technology uses feed-forward error correction to eliminate the distortion that is normally produced by the output stage.  No other audio amplifier comes close to delivering the clean, quiet, and robust power of the AHB2. DIFFICULT SPEAKER LOADS ARE HANDLED WITH EASE Many loudspeakers have frequencies at which their impedance drops to levels that are much lower than the "nominal" impedance. The AHB2 drives difficult phase angles and low impedances with ease. Stereo loads as low as 1.4 Ohms can be cleanly driven to full output levels. Most power amplifiers produce higher levels of distortion when the load impedance decreases. In contrast, the feed-forward error correction system in the AHB2 keeps the output clean when driving difficult loads. The AHB2 produces almost no measurable distortion at any rated load condition. In our quest to build the ultimate amplifier, we also focused on frequency response, output noise, drive current, damping factor, and reliability. The result is an amplifier that stands head and shoulders above the competition.

3.666 €
36 Δόσεις 126,56€ / μήνα
Κατόπιν Παραγγελίας

THE QUIETEST, CLEANEST AUDIO AMPLIFIER ON THE PLANET From the first watt to the last watt, no audio power amplifier offers lower noise or lower distortion than the Benchmark AHB2.Benchmark has raised the bar by introducing a new and revolutionary amplifier! TRUE HIGH-RESOLUTION PERFORMANCE  The AHB2 is the ideal match to the performance limits of High-Resolution-Audio (HRA) formats. Benchmark's AHB2 power amplifier delivers musical details without introducing the masking effects of amplifier noise and distortion. The dynamic range of the AHB2 is 132 dB, making it 10 to 30 dB quieter than some of the very best reference-quality power amplifiers. The frequency response of the AHB2 extends beyond 200 kHz. With the AHB2, you will discover previously overlooked nuances, dynamics, and detail in your favorite recordings and experience the full potential of the latest high-resolution 24-bit PCM and 1-bit DSD audio formats. EXPERIENCE THE EMOTION The musical details and emotion captured on today's finest High-Resolution-Audio recordings can only be fully appreciated when every component in the signal chain is capable of true high-resolution performance. Power amplifiers are a weak link in most audio systems. Most power amplifiers are well matched to the limitations of the CD format, but they fall well short of the capabilities of high-resolution formats. In contrast, the revolutionary AHB2 was specifically designed to deliver true high-resolution performance. FULFILLING THE NEED FOR BETTER AMPLIFICATION D/A conversion technology has outpaced the development of new power amplifiers. This means that the power amplifier has become a limiting factor in many audio systems. For example, the noise and distortion produced by the Benchmark DAC3 D/A converter is 20 to 30 dB lower than that produced by most high-quality power amplifiers. Until now, this meant that the DAC3 could not be fully appreciated. Benchmark set out to solve this problem by creating an amplifier that matches the performance of the DAC3. A RADICALLY DIFFERENT POWER AMPLIFIER We had to look beyond existing amplifier technologies and explore some new and radical solutions. In our search, we learned of two new patents on a new amplifier technology from THX. This was exactly the technology we needed to build our new amplifier. The AHB2 uses the new and revolutionary THX-patented AAA™ technology to virtually eliminate all forms of distortion. This technology uses feed-forward error correction to eliminate the distortion that is normally produced by the output stage.  No other audio amplifier comes close to delivering the clean, quiet, and robust power of the AHB2. DIFFICULT SPEAKER LOADS ARE HANDLED WITH EASE Many loudspeakers have frequencies at which their impedance drops to levels that are much lower than the "nominal" impedance. The AHB2 drives difficult phase angles and low impedances with ease. Stereo loads as low as 1.4 Ohms can be cleanly driven to full output levels. Most power amplifiers produce higher levels of distortion when the load impedance decreases. In contrast, the feed-forward error correction system in the AHB2 keeps the output clean when driving difficult loads. The AHB2 produces almost no measurable distortion at any rated load condition. In our quest to build the ultimate amplifier, we also focused on frequency response, output noise, drive current, damping factor, and reliability. The result is an amplifier that stands head and shoulders above the competition.

3.900 €
36 Δόσεις 134,64€ / μήνα
Κατόπιν Παραγγελίας

Stereo Power Amplifier This small stereo power amplifier shows everyone that size does not necessarily have anything to do with greatness. With the power of 570 W it has every speaker under control. Thanks to VOLTAiR technology, it is fast, precise and highly efficient with outstanding sound. Better safe than sorry The Performer s800 has a protection circuit against DC voltage and a limiter against output overload. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds. As one calls into the forest, so it echoes out. This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode. Trim to fit With reference to the s800, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB. This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier. In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode. Plus & Minus The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm. For bi-wiring operation, both types of connection can be used together. No loudspeaker with less than 4 ohms impedance may be connected. Bridge You can turn the two power amplifier channels into one power amplifier by connecting only the two plus pole terminals to the loudspeaker. This allows 450W into 8 Ohm in mono operation mode. AMP CTL The power amplifier can be switched on and off using the AMP CTL connection between the Performer s800 and a preamplifier such as the Director Mk2 or the Crossover. To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs. Third-party preamps can also switch the Performer s800 on and off with their 12 V trigger. Specifications: Analog Input & Thru: XLR (balanced) Input gain (max): 32.5 dB Input impedance (THRU not connected): 20 kΩ Common mode rejection (THRU not connected): -82 dB Input sensitivity: 6 dBu Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug Output power (RMS, 4 Ω): 570 W Output power (RMS, 8 Ω): 370 W Harmonic distortion (1 kHz, 8 Ω): < 0.03 % Output power (RMS, 8 Ω, Bridge Mode): 450 W Harmonic distortion (1 kHz, 8 Ω, Bridge Mode): < 0.011 % Output power (peak to peak): 74 V Output power (peak to peak, Bridge Mode): 180 V Output voltage (RMS): 35 V Output voltage (RMS, Bridge Mode): 86 V Output impedance (20 Hz – 20 kHz): < 0.031 Ω Output impedance (20 Hz – 20 kHz, Bridge Mode): < 0.043 Ω Amplification gain: 26 dB Amplification gain (Bridge Mode): 32 dB Damping factor (1 kHz, 8 Ohm): > 300 Damping factor (1 kHz, 8 Ohm, Bridge Mode): > 190 Frequency range (-3dB): 9 Hz – 200 kHz Noise (A-weighted): -123 dBu Internal Linear Power Supply with Shielded Toroidal Transformer Toroidal transformer: 875 VA Operating voltage (Input stage): +/- 60 V Operating voltage (power stage): +/- 60 V Operating voltage for relays, LEDs, AMP CTL: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse 230 V: T 4 mA Fuse 115 V: T 8 A Power consumption: max. 875 VA Idle power consumption: 40 W Stand-by power consumption: < 0.3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 100 x 375 mm Unit weight: 12.8 kg Shipping weight: 14 kg

2.998 €
36 Δόσεις 103,50€ / μήνα
Κατόπιν Παραγγελίας

Stereo Power Amplifier This small stereo power amplifier shows everyone that size does not necessarily have anything to do with greatness. With the power of 570 W it has every speaker under control. Thanks to VOLTAiR technology, it is fast, precise and highly efficient with outstanding sound. Better safe than sorry The Performer s800 has a protection circuit against DC voltage and a limiter against output overload. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds. As one calls into the forest, so it echoes out. This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode. Trim to fit With reference to the s800, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB. This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier. In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode. Plus & Minus The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm. For bi-wiring operation, both types of connection can be used together. No loudspeaker with less than 4 ohms impedance may be connected. Bridge You can turn the two power amplifier channels into one power amplifier by connecting only the two plus pole terminals to the loudspeaker. This allows 450W into 8 Ohm in mono operation mode. AMP CTL The power amplifier can be switched on and off using the AMP CTL connection between the Performer s800 and a preamplifier such as the Director Mk2 or the Crossover. To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs. Third-party preamps can also switch the Performer s800 on and off with their 12 V trigger. Specifications: Analog Input & Thru: XLR (balanced) Input gain (max): 32.5 dB Input impedance (THRU not connected): 20 kΩ Common mode rejection (THRU not connected): -82 dB Input sensitivity: 6 dBu Loudspeaker Outputs: Binding posts with ø4mm cable hole (screwable) and banana plug Output power (RMS, 4 Ω): 570 W Output power (RMS, 8 Ω): 370 W Harmonic distortion (1 kHz, 8 Ω): < 0.03 % Output power (RMS, 8 Ω, Bridge Mode): 450 W Harmonic distortion (1 kHz, 8 Ω, Bridge Mode): < 0.011 % Output power (peak to peak): 74 V Output power (peak to peak, Bridge Mode): 180 V Output voltage (RMS): 35 V Output voltage (RMS, Bridge Mode): 86 V Output impedance (20 Hz – 20 kHz): < 0.031 Ω Output impedance (20 Hz – 20 kHz, Bridge Mode): < 0.043 Ω Amplification gain: 26 dB Amplification gain (Bridge Mode): 32 dB Damping factor (1 kHz, 8 Ohm): > 300 Damping factor (1 kHz, 8 Ohm, Bridge Mode): > 190 Frequency range (-3dB): 9 Hz – 200 kHz Noise (A-weighted): -123 dBu Internal Linear Power Supply with Shielded Toroidal Transformer Toroidal transformer: 875 VA Operating voltage (Input stage): +/- 60 V Operating voltage (power stage): +/- 60 V Operating voltage for relays, LEDs, AMP CTL: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse 230 V: T 4 mA Fuse 115 V: T 8 A Power consumption: max. 875 VA Idle power consumption: 40 W Stand-by power consumption: < 0.3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 100 x 375 mm Unit weight: 12.8 kg Shipping weight: 14 kg

2.998 €
36 Δόσεις 103,50€ / μήνα
Κατόπιν Παραγγελίας

Our powerhouse mono-block. With the power of 1000 W this amplifier controls every loudspeaker effortlessly. Thanks to VOLTAiR technology it is fast, direct and highly efficient with an outstanding sound. Individual design The Performer m1000 can be equipped with a black, red or silver decorative panel that are included in the scope of delivery. This gives you a choice of three colour variants for your chosen basic colour. The decorative panels adhere with the help of a strong neodymium magnet. No tools are therefore required for changing them. Better safe than sorry The Performer m1000 has a protection circuit against DC voltage and a limiter against output overload. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds. As one calls into the forest, so it echoes out. This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode. Trim to fit With reference to the m1000, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB. This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier. In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode. Plus & Minus The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm. For bi-wiring operation, both types of connection can be used together. No loudspeaker with less than 2 ohms impedance may be connected. AMP CTL The power amplifier can be switched on and off using the AMP CTL connection between the Performer m1000 and a preamplifier such as the Director Mk2 or the Crossover. To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs. Third-party preamps can also switch the Performer m1000 on and off with a 12 V trigger. Keep cool Inside the Performer m1000, six fans usually do nothing at all, because 90% of the heat is passively dissipated via massive heat sinks. Should it nevertheless become really loud for a really long time, the processor-controlled fans remain virtually inaudible at only 19 dB (A). Specifications: Analog Input & Thru: XLR (balanced) Input gain (max): 32.5 dBu Input impedance (THRU not connected): 20 kΩ Common mode rejection (THRU not connected): -82 dBu Input sensitivity: 12.5 dBu Loudspeaker Output: Binding posts with ø4mm cable hole (screwable) and banana plug Output power (RMS, 2 Ω): 1000 W Harmonic distortion (1 kHz, 2 Ω): < 0.08 % Output power (RMS, 4 Ω): 750 W Harmonic distortion (1 kHz, 4 Ω): < 0.05 % Output power (RMS, 8 Ω): 420 W Harmonic distortion (1 kHz, 8 Ω): < 0.03 % Output power (peak to peak): 180 V Output voltage (RMS): 64.6 V Output impedance (20 Hz – 20 kHz): < 0.031 Ω Amplification gain: 26 dB Damping factor (1 kHz, 8 Ohm): > 280 Frequency range (-3dB): 10 Hz – 80 kHz Noise (A-weighted): -123 dB Internal Linear Power Supply with Shielded Toroidal Transformer Toroidal transformer: 1375 VA Operating voltage (Input stage): +/- 60 V Operating voltage (power stage): +/- 91 V Operating voltage for relays, LEDs, AMP CTL: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse 230 V: T 6.3 mA Fuse 115 V: T 12 A Power consumption: max. 1375 VA Idle power consumption: 50 W Stand-by power consumption: < 0.3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 205 x 375 mm Unit weight: 24.8 kg Shipping weight: 29.3 kg

3.900 €
36 Δόσεις 134,64€ / μήνα
Κατόπιν Παραγγελίας

Our powerhouse mono-block. With the power of 1000 W this amplifier controls every loudspeaker effortlessly. Thanks to VOLTAiR technology it is fast, direct and highly efficient with an outstanding sound. Individual design The Performer m1000 can be equipped with a black, red or silver decorative panel that are included in the scope of delivery. This gives you a choice of three colour variants for your chosen basic colour. The decorative panels adhere with the help of a strong neodymium magnet. No tools are therefore required for changing them. Better safe than sorry The Performer m1000 has a protection circuit against DC voltage and a limiter against output overload. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds. As one calls into the forest, so it echoes out. This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode. Trim to fit With reference to the m1000, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB. This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier. In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode. Plus & Minus The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm. For bi-wiring operation, both types of connection can be used together. No loudspeaker with less than 2 ohms impedance may be connected. AMP CTL The power amplifier can be switched on and off using the AMP CTL connection between the Performer m1000 and a preamplifier such as the Director Mk2 or the Crossover. To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs. Third-party preamps can also switch the Performer m1000 on and off with a 12 V trigger. Keep cool Inside the Performer m1000, six fans usually do nothing at all, because 90% of the heat is passively dissipated via massive heat sinks. Should it nevertheless become really loud for a really long time, the processor-controlled fans remain virtually inaudible at only 19 dB (A). Specifications: Analog Input & Thru: XLR (balanced) Input gain (max): 32.5 dBu Input impedance (THRU not connected): 20 kΩ Common mode rejection (THRU not connected): -82 dBu Input sensitivity: 12.5 dBu Loudspeaker Output: Binding posts with ø4mm cable hole (screwable) and banana plug Output power (RMS, 2 Ω): 1000 W Harmonic distortion (1 kHz, 2 Ω): < 0.08 % Output power (RMS, 4 Ω): 750 W Harmonic distortion (1 kHz, 4 Ω): < 0.05 % Output power (RMS, 8 Ω): 420 W Harmonic distortion (1 kHz, 8 Ω): < 0.03 % Output power (peak to peak): 180 V Output voltage (RMS): 64.6 V Output impedance (20 Hz – 20 kHz): < 0.031 Ω Amplification gain: 26 dB Damping factor (1 kHz, 8 Ohm): > 280 Frequency range (-3dB): 10 Hz – 80 kHz Noise (A-weighted): -123 dB Internal Linear Power Supply with Shielded Toroidal Transformer Toroidal transformer: 1375 VA Operating voltage (Input stage): +/- 60 V Operating voltage (power stage): +/- 91 V Operating voltage for relays, LEDs, AMP CTL: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse 230 V: T 6.3 mA Fuse 115 V: T 12 A Power consumption: max. 1375 VA Idle power consumption: 50 W Stand-by power consumption: < 0.3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 205 x 375 mm Unit weight: 24.8 kg Shipping weight: 29.3 kg

3.900 €
36 Δόσεις 134,64€ / μήνα
Κατόπιν Παραγγελίας

Our powerhouse mono-block. With the power of 1000 W this amplifier controls every loudspeaker effortlessly. Thanks to VOLTAiR technology it is fast, direct and highly efficient with an outstanding sound. Individual design The Performer m1000 can be equipped with a black, red or silver decorative panel that are included in the scope of delivery. This gives you a choice of three colour variants for your chosen basic colour. The decorative panels adhere with the help of a strong neodymium magnet. No tools are therefore required for changing them. Better safe than sorry The Performer m1000 has a protection circuit against DC voltage and a limiter against output overload. If direct current (DC) is detected, the output stage switches off automatically and the Protect LED lights up red. To protect the output against overdriving, an LDR limiter (light-dependent resistor) is used. Since it works optically, the audio quality is not affected. The Protect LED lights up yellow when the limiter responds. As one calls into the forest, so it echoes out. This saying inspired us to send the input signal out again in order to drive another power amplifier in bi-amping mode. Trim to fit With reference to the m1000, “fit” means adapted. And you can adapt the input sensitivity in 0.5 dB steps. From 0 dB to -5.5 dB. This is the much more audiophile solution for acoustically problematic rooms or loudspeaker set-ups than the panorama potentiometer of the preamplifier. In addition, the difference in loudness of loudspeakers can be elegantly compensated in bi-amping mode. Plus & Minus The loudspeaker binding posts can accommodate banana plugs as well as a stranded wire with a diameter of up to 4mm. For bi-wiring operation, both types of connection can be used together. No loudspeaker with less than 2 ohms impedance may be connected. AMP CTL The power amplifier can be switched on and off using the AMP CTL connection between the Performer m1000 and a preamplifier such as the Director Mk2 or the Crossover. To do this, connect the 3.5 mm jack sockets with a cable with 3.5 mm mono or stereo jack plugs. Third-party preamps can also switch the Performer m1000 on and off with a 12 V trigger. Keep cool Inside the Performer m1000, six fans usually do nothing at all, because 90% of the heat is passively dissipated via massive heat sinks. Should it nevertheless become really loud for a really long time, the processor-controlled fans remain virtually inaudible at only 19 dB (A). Specifications: Analog Input & Thru: XLR (balanced) Input gain (max): 32.5 dBu Input impedance (THRU not connected): 20 kΩ Common mode rejection (THRU not connected): -82 dBu Input sensitivity: 12.5 dBu Loudspeaker Output: Binding posts with ø4mm cable hole (screwable) and banana plug Output power (RMS, 2 Ω): 1000 W Harmonic distortion (1 kHz, 2 Ω): < 0.08 % Output power (RMS, 4 Ω): 750 W Harmonic distortion (1 kHz, 4 Ω): < 0.05 % Output power (RMS, 8 Ω): 420 W Harmonic distortion (1 kHz, 8 Ω): < 0.03 % Output power (peak to peak): 180 V Output voltage (RMS): 64.6 V Output impedance (20 Hz – 20 kHz): < 0.031 Ω Amplification gain: 26 dB Damping factor (1 kHz, 8 Ohm): > 280 Frequency range (-3dB): 10 Hz – 80 kHz Noise (A-weighted): -123 dB Internal Linear Power Supply with Shielded Toroidal Transformer Toroidal transformer: 1375 VA Operating voltage (Input stage): +/- 60 V Operating voltage (power stage): +/- 91 V Operating voltage for relays, LEDs, AMP CTL: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse 230 V: T 6.3 mA Fuse 115 V: T 12 A Power consumption: max. 1375 VA Idle power consumption: 50 W Stand-by power consumption: < 0.3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 205 x 375 mm Unit weight: 24.8 kg Shipping weight: 29.3 kg

3.900 €
36 Δόσεις 134,64€ / μήνα
Κατόπιν Παραγγελίας

At 2 x 200 Watts per channel and utilising Rotel's Balanced Design Concept for superior performance, the RB-1582 MkII is a compelling stereo amplifier. Rotel’s next largest stereo amplifier at 200 Watts per channel provides the massive current to drive the very largest Hi-Fi systems effortlessly. And like its smaller brother, the RB-1582 MkII has been designed to excel at resolving the subtle details in music as well as supplying the brawn required for extremely dynamic passages. It is able to achieve this difficult dual requirement because of the meticulous attention paid to circuit design and parts selection. The RB-1582 MkII's high-end performance begins with an extremely large toroidal transformer combined with a total of 60,000µF storage capacity in special “slit foil” capacitors to provide completely stable power to the output stage. Slit foil capacitors have the ability to charge and discharge extremely quickly, thereby ensuring signal fidelity during orchestral crescendos or repetitive kick-drum impacts, for example. Both left and right channel construction are laid out in a mono block design (after the toroidal transformer) and all grounding is terminated in a star pattern on a copper grounding plate to ensure low signal to noise. The output stage is a discrete design that consists of 10 high current bipolar transistors per channel. Input options consist of both balanced XLR and unbalanced RCA connectors. The RB-1582 MkII stereo power amplifier is yet another outstanding example of Rotel’s Balanced Design Concept and will form the heart of a very impressive stereo or home theatre system for years to come. Specifications: DIMENSIONS:  (W × H × D)431 × 144 × 407mm, 17" × 5.7" × 16" FRONT PANEL HEIGHT: 3U / 132.6mm (5.25") POWER REQUIREMENTS: 230V, 50Hz POWER CONSUMPTION: 550W STANDBY POWER CONSUMPTION: 0.5W NET WEIGHT: 17.6kg (39lbs.) BTU RATING: (4Ω, 1/8th power)1104 BTU/hComponents CONTINUOUS POWER OUTPUT: 200W/Ch (All channels driven, 8Ω) TOTAL HARMONIC DISTORTION (THD)(20Hz–20kHz)

1.480 €
36 Δόσεις 51,09€ / μήνα
Κατόπιν Παραγγελίας

At 2 x 200 Watts per channel and utilising Rotel's Balanced Design Concept for superior performance, the RB-1582 MkII is a compelling stereo amplifier. Rotel’s next largest stereo amplifier at 200 Watts per channel provides the massive current to drive the very largest Hi-Fi systems effortlessly. And like its smaller brother, the RB-1582 MkII has been designed to excel at resolving the subtle details in music as well as supplying the brawn required for extremely dynamic passages. It is able to achieve this difficult dual requirement because of the meticulous attention paid to circuit design and parts selection. The RB-1582 MkII's high-end performance begins with an extremely large toroidal transformer combined with a total of 60,000µF storage capacity in special “slit foil” capacitors to provide completely stable power to the output stage. Slit foil capacitors have the ability to charge and discharge extremely quickly, thereby ensuring signal fidelity during orchestral crescendos or repetitive kick-drum impacts, for example. Both left and right channel construction are laid out in a mono block design (after the toroidal transformer) and all grounding is terminated in a star pattern on a copper grounding plate to ensure low signal to noise. The output stage is a discrete design that consists of 10 high current bipolar transistors per channel. Input options consist of both balanced XLR and unbalanced RCA connectors. The RB-1582 MkII stereo power amplifier is yet another outstanding example of Rotel’s Balanced Design Concept and will form the heart of a very impressive stereo or home theatre system for years to come. Specifications: DIMENSIONS:  (W × H × D)431 × 144 × 407mm, 17" × 5.7" × 16" FRONT PANEL HEIGHT: 3U / 132.6mm (5.25") POWER REQUIREMENTS: 230V, 50Hz POWER CONSUMPTION: 550W STANDBY POWER CONSUMPTION: 0.5W NET WEIGHT: 17.6kg (39lbs.) BTU RATING: (4Ω, 1/8th power)1104 BTU/hComponents CONTINUOUS POWER OUTPUT: 200W/Ch (All channels driven, 8Ω) TOTAL HARMONIC DISTORTION (THD)(20Hz–20kHz)

1.480 €
36 Δόσεις 51,09€ / μήνα
Κατόπιν Παραγγελίας

AN IMMERSIVE LISTENING EXPERIENCE THE HIGH-POWER SUBWOOFER AMPLIFIER  Designed for integration, with rack-mountable design, 100 IWSUB8 Amplifier delivers a peak power of 200 watts and a continuous power of 150 watts under 4 ohms, whilst ensuring a high-level electronic protection. Specially tailored for the passive subwoofer 100 IWSUB8, this amplifier is able to power up to two subwoofers connected in parallel.   This powerful combination is the ideal add-on to a 100 Series audio/video setup, delivering an unique ambiance and sound coverage in your living spaces. Key Points: Peak power: 200W (continuous power : 150W under 4Ώ). Amplifier able to drive 2 x 100 IWSUB8 subwoofers connected in parallel. High-level electronic protection (dynamic power control, thermal protection, short circuit, fuse, and over-current protection). Flush potentiometers. Dimensions (HxWxD): 1¾ x 16⅞ x 10⅛" [44.5 x 429 x 257mm]  - Height with stands: 2⅟16"  - Width with brackets: 19" Technical Specifications: Type: Subwoofer amplifier Power (continuous): Max 200W, 150W continuous (4Ώ) Minimum load: 4Ώ Voltage range: 100-120V~60Hz / 220-230V~50Hz Power consumption: 150W Stand-by power consumption: 0.5W Bandwith: 20-250Hz Subsonic filter: 18dB/oct. Inputs: LFE, Line in L/R Outputs: Line out L/R and subwoofer power output on speaker terminal Cord: Detachable IEC power cord Protection: Dynamic power control, thermal protection, short circuit, fuse, and over-current protection Dimensions (HxWxD): [44.5 x 429 x 257mm]  1 3/4 (2 1/16 with stands) x 16 7/8 (19 with brackets) x 10 1/8" Net weight: 6.8lbs (3.1kg)

980 €
12 Άτοκες Δόσεις 81,67€ / μήνα
Κατόπιν Παραγγελίας

Crafted for pure musical performance, Statement is the pinnacle of Naim Audio engineering knowledge and artistry. The series comprises the NAC S1 preamplifier and NAP S1 mono power amplifiers.  Origins The idea for an entirely new kind of amplifier was first conceived by our engineers over a decade ago and development began in earnest in 2011. The objective was to set a new reference standard in high-end audio and music reproduction. The result is Statement. Three years of relentless questioning, iterative design and a point blank refusal to accept no as an answer. Performance First Engineering Product engineers often begin with what exists already. They might ask how something can work better, or where improvements can be made. With Statement, we started with a blank sheet of paper and a vision: to create the ultimate amplifier. After the initial concept stage the engineering team set aside practical considerations and began to map out the product in free space. This creative freedom was then backed up by 3D computer models which confirmed the optimum position for each component. To accommodate this new layout Statement pioneers a new vertical structure. It was the best way to minimise electromagnetic and mechanical interference and maximise thermal performance. Duality In Design Statement's radically different aesthetic may seem like a departure from Naim Audio tradition but it's the ultimate expression of everything we represent. The imposing monolithic structure with its stark silhouette is offset by the organic sculptural flow of the heat sink and the beautifully lit volume control and central divide. This duality in the design reflects how our pursuit of technical brilliance is always grounded in the abstract human experience of music. If it's the best amplifier in the world in lab tests we’ve only done half a job - it's in the listening room where it really counts. Technology Everything about Statement is a leap forward in technology and design. It's been engineered from the ground up for pure performance. Isolation Statement perfectly represents our philosophy of providing the highest quality power supply, while isolating individual sections to avoid unwanted interference. The NAC S1 and NAP S1 share the same fundamental layout. The noisy power supply is housed in the base and sensitive electronics are nestled above. Each section is divided by an acrylic centre-piece that blocks interaction. Top section electronics are separated further still, with internal chambers isolating individual stages. Dual Power The Statement NAP S1 features a new bridged dual design with zero global feedback. The two stages are physically separated to optimise the amplifier circuit with the delicate voltage stage at the very top of the power amplifier, away from the current stage at the bottom. Each mono power amplifier uses a huge 4000VA transformer to power speakers with precisely 746W (into 8 ohms). Precision engineering also makes sure every single watt is delivered right to where it's needed, when it's needed. After all, power is nothing without purpose. Craft Every component, curve and connection in Statement demanded new levels of engineering and tolerance. Metallurgy The distinctive ‘wave’ heat sinks begin life as a solid billet of untreated aluminium, which is cut to size and machined to achieve the curved profile. The fins are then cut using a five-axis, temperature-controlled, CNC machine. It takes three hours for the finished shape to emerge. Once each piece is individually machined, it is painstakingly hand-polished and quality inspected. Finishing After the inspection process, the metalwork is submerged in baths of cleansing acid and then into a bath of electrolyte fluid containing black ink. A current is passed through it, bonding the ink to the metalwork and creating Naim Audio's signature black finish. It took several months of collaboration between our engineers and suppliers to achieve the finish Statement demanded. Hand-Crafting Statement has been designed and developed using cutting-edge manufacturing technology. But it takes a human touch to get things just right. For example, every sound-critical component is positioned and soldered by hand by our skilled technicians. As with all Naim Audio products final assembly is carried out by hand in Wiltshire, England. NAP S1 Audio Inputs: Analogue Input: 1 x XLR (each) Audio Outputs: Audio Outputs: Binding posts for spade & 4mm banana Power Output: 746W into 8 ohms, 1450W into 4 ohms, 9kW burst power into 1 ohm Physical: Weight: 101kg (each) Dimensions (HxWxD): 940 x 256 x 383mm (each)

154.990 €
12 Άτοκες Δόσεις 12.915,83€ / μήνα
Κατόπιν Παραγγελίας