Τελικοί Ενισχυτές

The Manley 500 and 250 Watt Monoblocks are our most powerful push-pull production-models. Both the circuit design and the selected componentry have been refined over years and years of development. Reliability that you can depend upon combined with musical accuracy and emotional authority is what these amplifiers promise- and deliver. They are able to switch operation modes allowing the listener to choose between the sonically seductive qualities of triode and the more powerful Ultra-Linear configuration. We use big, beefy reservoir capacitors in the high voltage supplies giving plenty of instant energy for dynamic performance of transient peaks and bass impact and weight which often exceeds that of rival solid-state amplifiers.Χαρακτηριστικά:ALL-TUBE monoblock design 10 x KT90EH Electro-Harmonix Russian output tubesHigh current double 12BH7EH driver stage12AT7EH large plate Electro-Harmonix Russian input tubeBALANCED & UNBALANCED inputsMUTE switchTRIODE / Ultra-Linear switchingSOFT-START/ EVER-WARM standby modeMANLEY Precision output transformerFactory set for 5 Ohms nominalFront panel bias measurement and adjust (hiding under the black insert)Large filter / reservoir capacitors 3800uF x 2Angled rear of chassis provides for easy connectionsWBT binding postsInput sensitivity: 1VGain: 32dB tetrode; 30dB in triodeInput Impedance RCA: 116 kOhm  1KHzInput Impedance XLR: 270 kOhm  1KHz - 20 kOhms  20KHz - 38 kOhm  20HzNoise Floor: Tetrode: -67dB; Triode -65dB typicalS/N Ratio: -80 dBDynamic Range: 96dBFLAT frequency response: 10 Hz - 30 KHz continuousPower Consumption: 30 Watts in "EVER-WARM"Full power (tetrode): 500WFull power (triode): 275WFactory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.Mains Voltage Frequency:Dims: W=19", D=13", H=9"Shipping weight: 82 lbs. each

These cute little guys produce around 40 watts RMS in Ultra-Linear mode or around 20 watts in TRIODE from a quartet of EL84 / 6BQ5 tubes driven by a 6414 dual triode driver and a 12AT7EH input dual triode.Χαρακτηριστικά:Input Tube: 1 x 12AT7EH large plate Eletcro-Harmonix RussianDriver Tube: 1 x 6414 JAN NOS GE or Raytheon brandedOutput Tubes: 8 x EL84 Ships with Russian NOS EL84M (aka 6Pi14Pi-EB) We are out of Ei 6BQ5.Output Tube Quiescent Standing Current: 25mASet Bias for 250mVDC measured across each 10 Ohm cathode resistorInput Impedance: 110 kOhmNegative Feedback: MIN= 3dB; STD=6dB; MAX=10dB of global NFBGain:TRIODE/ULFB MIN: 30.7 dB 32.1 dBFB STD: 28.5 dB 29.1 dBFB MAX: 26.1 dB 27.1 dBInput Sensitivity for Maximum Output Power: defined as input voltage required in order to produce maximum power output reaching 1.5% THD  1KHzTRIODE/ULFB MIN: 175mV 155mVFB STD: 312mV 340mVFB MAX: 480mV 566mVInput Sensitivity for 1W into 8 Ohms: 61mV 53mVMaximum Output Power: defined as power output reaching 1.5% THD  1KHzSignal to Noise Ratio Ref. 1W: Typically 82 dB A-WGT 20-20KNoise Floor: Typically 150µV = -74dBu A-WGTNoise Floor: Typically 650µV = -62dBu unweightedWill Scratch Your Floor: Use pennies under pointed feet to avoid marring cabinetry. Try quarters if you are in upper tax brackets. The bargain performer would be nickels. Paper currency does not function as well. Euro coins work 1.54 times better. Concrete pavers or wooden chopping blocks serve fine for amplifier platforms.Dynamic Range: 83dBTHD+Noise  5W: less than 0.15%Frequency Response at full power UL mode w/MAX NFB: 20 Hz to 20 kHz FLATFrequency Response at 5W into 5 Ohms: 10 Hz to 30 kHz FLAT, -3.75dB  100KHzRecommended Speaker Load: Optimized for 5 OhmsOutput Impedance:TRIODE / ULFB MIN: 2.43 Ohms TRIODE; 3.10 Ohms ULFB STD: 1.47 Ohms TRIODE; 1.67 Ohms ULFB MAX: 0.90 Ohms TRIODE; 0.95 Ohms ULDamping Factor:TRIODE / ULFB MIN: 3.29 TRIODE; 2.58 ULFB STD: 5.45 TRIODE; 4.78 ULFB MAX: 8.90 TRIODE; 8.43 ULPower Consumption (idle): 102 Watts (0.85A  120VAC)Maximum Power Consumption (at Full Power): 168 Watts (1.4A  120VAC)Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.Mains Voltage Frequency: 50 ~ 60 HzFuse type and ratings  117 VAC operation:MAINS fuse: 3 Amp 3AG slow-blow use glass body Littlefuse Series 239Fuse type and ratings  230 VAC operation:MAINS fuse: 1.6 Amp 3AG slow-blow use glass body Littlefuse Series 239B+ Fuse: MDA 400 mA SLO-BLO Ceramic Time-Delay fuseBadge Illumination: Units produced before 3/2003 use 8V, 0.3A "Fuse-Lamp" 1/4" X 1 1/4" - Serial numbers after MAHI036 use LED illumination which probably won't burn outDimensions: 11" deep x 10" wide x 5" tallShipping weight each: 18 pounds

In 2002 we launched a very tasty all-tube 100 watt monoblock called The Snapper. Another brilliant design from Mitch Margolis features a quartet of EL34 or 6CA7 or KT77's in a fully differential circuit topology, including the input and driver stages. This Snapper can be driven fully balanced all the way through via the XLR inputs.Χαρακτηριστικά:100 Watt partial triode (UltraLinear) EL-34 output stage is tolerant of a wider variety of output load conditions than pure pentode.Precise and balanced signal path from input to output. Circuit self-balances with either single-ended or balanced inputs. [Don't let either speaker terminal contact chassis, earth or any other ground.Switch-selectable RCA unbalanced inputs, or XLR balanced inputs. RCA jack input impedance about 330 kOhms, XLR 15 kOhms. If one input is not occupied, the input selector switch may then be used as a poor-man's MUTE switch. Handy for checking the bias, swapping input cables, etc..Input Sensitivity RCA jack: 750 mV RMS for full output into 5 OhmsInput Sensitivity RCA jack: 71 mV RMS for 1 watt output into 8 OhmsInput Sensitivity XLR jack: 1.5 V RMS for full output into 5 OhmsOverall voltage gain RCA jack to Output: 31 dBu, or about 32 volts per volt.Signal to A-weighted noise ratio on Humberto's bench is about 110 dB.Damping Factor: 4.7All-balanced amp topology keeps B+ voltage variations from degrading the performance of the input and driver stages. This technique can help make a push-pull amplifier very revealing of signal detail, in part by canceling power-supply-related perturbations and increasing signal-to-noise ratios.Portly 180 Joule energy storage reservoir in the main B+ supply channel for explosive transient response and athletic musical stamina. Also reduces B+ fluctuations due to varying current demands of output stage.Wideband transformerless balanced input with bridged 15 kOhm input impedance. Balanced input sensitivity may be selected by changing one resistor to suit whatever operating level may be required. 0 dBu, +4, +8, etc... If desired, the user may safely ground either pin 2 or 3 for single-ended drive of the balanced XLR input... [Be careful NOT to drive pins 2 and 3 of the XLR with a large common-mode signal, or the internal B+ fuse could blow.]Quiet DC supply for the input and driver tube filaments.Excellent square-wave response, and very low excess phase-shift with frequency.Amp actually puts out 110W  5 Ohm load  2 kHz  onset of clipping, 117 VAC mains voltage, 3.5 amps mains current.100 W spec: 15 Hz - 40 kHz into 5 OhmsPuts out 100W into an 8 Ohm load.Snapper unit weight: 38 lbs.

The wonderfully simple 300B directly heated triode is virtually Lee De Forest's very first evolutionary 3-element piece, comprising only filament, input grid and anode output. Brought to reliable perfection by Western Electric USA and later by Standard Telephones UK as the 4300B, the 300B was very much intended and widely used for telephony amplification.Χαρακτηριστικά:Vacuum Tubes: 2 x 300B (Output), 1 x 6SN7 (Driver), 1 x 6SL7 (Input),2 x 5AR4 (Rectifier). (Units prior to 2011 used 5U4 rectifier tubes.)Output Power  1kHz with 5 dB FeedBack in SINGLE-ENDED: 11 Watts  3% THDOutput Power  1kHz with 5 dB FeedBack in PUSH-PULL: 24 Watts  1.5% THDFrequency Response with 5 dB FB in SINGLE-ENDED: 15 Hz - 15 kHz ±0.5 dB (measured at 5 watts)Frequency Response with 5 dB FB in PUSH-PULL: 10 Hz - 20 kHz ±0.5 dBGAIN SE Mode 0dB Feedback Setting: 30 dBGAIN SE Mode 10dB Feedback Setting: 20 dBInput Sensitivity with 5db FB SINGLE ENDED: 700mV for Maximum PowerInput Sensitivity with 5db FB PUSH-PULL: 450mV for Maximum PowerInput Sensitivity with 5db FB SINGLE ENDED: 165mV for 1V output into 8 OhmsInput Sensitivity with 5db FB PUSH-PULL: 160mV for 1V output into 8 OhmsS/N Ratio: SINGLE ENDED: 83.5dB Ref. 1W; 2.83v//8 Ohms,20KHz BW; 5dB FB.S/N Ratio: PUSH-PULL: 85.4dB Ref. 1W; 2.83v//8 Ohms; 20KHz BW; 5dB FB.Dynamic Range: SINGLE ENDED: 94dB Ref. 3% THD; 20KHz BW; 5dB FB.Dynamic Range: PUSH-PULL: 99.5dB Ref. 1.5% THD; 20KHz BW; 5dB FB.Input Impedance: 100 kOhm, direct coupled.Optimum Speaker Load (switchable): 4 to 12 Ohm range appropriate for 4 & 8 Ohm speakers - 12 to 20 Ohm range appropriate for 16 Ohm speakersActual Output Impedance SINGLE ENDED: 2.25 OhmsActual Output Impedance PUSH-PULL: 1.86 OhmsDamping Factor SINGLE ENDED: 3.5Damping Factor PUSH-PULL: 4.3Maximum Power Consumption: 240 WattsMains Voltage Frequency: 50~ 60HzPower transformer factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.Fuse type and ratings  117 VAC operation:MAINS fuse: 3 Amp 3AG slow-blow use glass body Littlefuse Series 239Fuse type and ratings  230 VAC operation:MAINS fuse: 1.6 Amp 3AG slow-blow use glass body Littlefuse Series 239B+ Fuse: MDA 400 mA SLO-BLO Ceramic Time-Delay fuseBadge Illumination: Units produced before 7/2003 use 8V, 0.3A "Fuse-Lamp" 1/4" X 1 1/4" - Serial numbers after NSEPP314 use LED illumination which probably won't burn outDimensions: W= 8.5, D= 23, H= 9 inches, Including projecting controls and partsMinimum Mounting Surface Dimensions: Feet Footprint = W= 7.5" D= 18"Shipping Weight: 41 lbs. Each.

The Manley 500 and 250 Watt Monoblocks are our most powerful push-pull production-models. Both the circuit design and the selected componentry have been refined over years and years of development. Reliability that you can depend upon combined with musical accuracy and emotional authority is what these amplifiers promise- and deliver. They are able to switch operation modes allowing the listener to choose between the sonically seductive qualities of triode and the more powerful Ultra-Linear configuration. We use big, beefy reservoir capacitors in the high voltage supplies giving plenty of instant energy for dynamic performance of transient peaks and bass impact and weight which often exceeds that of rival solid-state amplifiers.Χαρακτηριστικά:ALL-TUBE monoblock design: uses 10 x EL34JJ output tubesDriver Stage: High current double 12BH7EH (x2) Electro-Harmonix RussianInput Tube: 12AT7EH large plate Electro-Harmonix RussianBALANCED & UNBALANCED inputs: RCA and XLR jacks (switchable)MUTE switch: on front panelTRIODE / Ultra-Linear output mode switching: on front panelSOFT-START turn on mode: minimizes in-rush current by first powering up amplifier to half voltagesEVER-WARM mode: for standby keeps tubes warmed up at half voltagesMANLEY Precision Output Transformer: designed and wound at Manley LabsFront panel bias measurement and adjust: Concealed under the black oval insertOutput Tube Standing Current: 27.5mASet Bias for: 275mVDC measured across each bias tip jack to groundLarge filter / reservoir capacitors: 3800uF x 2Angled rear of chassis: provides for easy connectionsWBT binding posts: CE compliant for European modelsInput Sensitivity RCA: Triode = 1.637 V, Tetrode = 1.837 V for full powerInput Sensitivity XLR: Triode = 3.2 V, Tetrode = 3.6 V for full powerInput Sensitivity Triode: 174mV for 1 watt into 8 OhmsInput Sensitivity Tetrode: 146mV for 1 watt into 8 OhmsGain Triode: 30dBGain Tetrode: 32dBInput Impedance RCA: 116 kOhm  1KHzInput Impedance XLR: 270 kOhm  1KHz - 20 kOhms  20KHz - 38 kOhm  20HzActual Output Impedance Triode: 0.538 OhmActual Output Impedance Tetrode: 0.465 OhmOptimum Speaker Load: 5 OhmsDamping Factor Triode: 14.8Damping Factor Tetrode: 17.2S/N Ratio Ref 1W into 8 Ohms: -80 dB -90dB A-WGTDynamic Range: 93dBFLAT frequency response: 10 Hz - 30 KHz continuousFull Power Tetrode: 250W  1.5% THD into 5 OhmsFull Power Triode: 100W  1.5% THD into 5 OhmsPower Consumption: 30 Watts in "EVER-WARM" modeMaximum Power Consumption: 815 Watts at full powerOperating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.Mains Voltage Frequency:Mains Fuse 100-120VAC operation: MDA 10 Amp SLO-BLO Ceramic Time-Delay fuseMains Fuse 220-240VAC operation: MDA 8 Amp SLO-BLO Ceramic Time-Delay fuseB+ Fuse: MDA 1 1/2A SLO-BLO Ceramic Time-Delay fuseBadge Illumination: Units produced before 4/2003 use 8V, 0.3A "Fuse-Lamp" 1/4" X 1 1/4" - Serial numbers after N250188 use LED illumination which probably won't burn outPower Cord: Detachable IEC standard. Appropriate power cord supplied for destination countryDimensions: W=19" x D=13" x H=9"Shipping Weight: 73 Lbs. each

The famous Manley Stingray stereo integrated amplifier has been renewed and refreshed. Allow us to present to you the Stingray II integrated tube amplifier with full featured RF and IR remote control.The STINGRAY II is the next evolution from our acclaimed Stingray Integrated Amplifier, legendary in the hifi world since it first swam from our labs in 1997. Originally conceived with particular attention paid to optimal component placement for the purity and symmetry of the signal path layout, the Stingray quickly became one of our best-selling products.Χαρακτηριστικά:3 x Stereo Line RCA Inputs1 x Stereo Line 1/8" TRS mini-jack InputTRIODE - UL Output Stage Mode SwitchingRECORDING OUTSUBWOOFER OUTTAPE LOOP (Insert) with Bypass switch1/4" Headphone OUTPUT (mutes speakers and subwoofer output when deployed)Logic controlled Volume and Balance functionsAll-Vacuum Tube Lo-feedback Stereo Integrated DesignOutput Tubes: 8 x EL84 Ships with Russian NOS EL84M (aka 6Pi14Pi-EB)Driver Tubes: 2 x 6414 Ships with GE or RAYTHEON JAN NOS USA or 6414WInput Tubes: 2 x 12AT7EH Ships with: 12AT7EH large plate Electro-Harmonix Russian

Πολυκάναλος τελικός ενισχυτής MM7055.Χαρακτηριστικά:Ισχύς Εξόδου: 5 x 140 W (8 ohms), 5 x 170 W (4 ohms)Είσοδοι: 5x Balanced In, 5x Main-inΈξοδοι: -Χειριστήριο: ΌχιΔιαστάσεις (Π x Υ x Β): 440 x 183 x 384 χιλ.Βάρος: 15,2 κιλάΛοιπά Χαρακτηριστικά: High Grade Audio Components, Customised Components, Input buffer amp (all inouts)

Στερεοφωνικός τελικός ενισχυτής MM7025 2 x 140W RMS 8 ohm, Μέτρο ισχύος σε κυκλική θέση, Κύκλωμα Ανατροφοδότησης Ρεύματος, Ισορροπημένες είσοδοι, Επιχρυσωμένοι ακροδέκτες ηχείων, Είσοδοι ελέγχου DC trigger, Απομακρυσμένος δίαυλος της Marantz, Διατίθεται σε μαύρο χρώμα.Χαρακτηριστικά:Power Output (8 / 4 Ohm RMS)140 W / 170 W (6)Power Output (8 / 4 Ohm DIN)-Power Output (8 / 4 Ohm IHF)-Bridged Power Output (8 Ohm RMS)-Frequency Response8 Hz-100 kHz (+-3 dB)Total Harmonic Distortion0.03% (20 Hz - 20 kHz)Damping Factor100Input Sensitivity: MM-Input Sensitivity: MC-Signal to Noise Ratio: MM / MC-Input Sensitivity: High level1.2 V / 22 KInput Sensitivity: Balanced High level2.4 V / 30 KSignal to Noise Ratio: High level105 dB  

Mονοφωνικός τελικός ενισχυτής με λυχνίες EL34Β.Προδιαγραφές:  Ισχύς: 80 wattAπόκριση συχνότητας: 16Hz-100KHz +-1 dBΠαραμόρφωση:

State-of-the-art μονάδα ενίσχυσης με εξαιρετική ακρίβεια των χαμηλών και των υψηλών συχνοτήτων σχεδιασμένος για biamped και bridged συστήματα . Η ισχύς του είναι 300W  και τοποθετείται στις βάσεις των ηχείων καθιστόντας τις απώλειες από την μεταφορά σήματος μηδαμινές καθώς τα καλώδια μπορούν να είναι πολύ μικρού μήκους .Σε χρήση biamped έχουμε πολύ καλύτερες μικροδυναμικές στόν ήχο. Σε bridged mode η ισχύς του ανέρχεται στα 600 W το κανάλι.Όπως και τα ηχεία, ένας απο τούς καλύτερους ενισχυτές που κατασκευάστηκαν ποτε ανεξαρτήτως τιμής. Απίστευτη τονική ισσοροπία, άνεση και ταχύτητα.            ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ    Output power: 1 channels: 200W @ 8ohms, 300W @ 4ohms,Gain: 30/35dB,Bandwidth: 1Hz–50kHz -3db,Integrated high pass filter optimized for L-505A/L-707,THD+noise: 0.01% THD @ 50W,

Οι ενισχυτές Lipinski είναι dual topology, αυτό σημαίνει ότι υπάρχουν δύο ξεχωριστοί ενισχυτές. Ο L-400 subwoofer amplifier  δουλέυει σε  parallel mode, που βελτιώνει αισθητά το damping factor , την πιο σημαντική παράμετρο για την απόδοση των χαμηλών συχνοτήτων.        ΧΑΡΑΚΤΗΡΙΣΤΙΚΑOutput power: 1 channels: 200W @ 8ohm, 300W @ 4ohm, 400W @ 2ohm,1 Ohm stable,Gain: 30-40dB,Bandwidth: 1Hz–150Hz,Integrated low pass filter optimized for L-505A/L-707,THD+noise: 0.01% THD @ 50W, 1000 below 100Hz,Input impedance: 10kohms,Inputs: 2x XLR, 2x RCA,Multi color front glass light,Dimensions: 17.3"H x 3.1"W x 8.7"D (44cm x 8cm x 22cm),Weight: 33 lbs (15 kg).