Car Amplifiers
The FPX 4.800 is a very compact 4-channel amplifier with a power of 4x120 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.800 is the most versatile model in this range. Thanks to its very high power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair output lines. The high power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line. Optimised Heat Dissipation For an amplifier to provide high power and musicality, efficiency and heat dissipation are two essential qualities. In order to optimise these aspects, FPX amplifiers have been given a thick aluminum chassis. The distribution of the components on the motherboard was also carefully researched to optimise the cooling capacity of the chassis. The careful selection of each Class D component (switching power supply, oversized toroidal transformers and high-quality capacitors) has made it possible to create powerful but ultra-compact amplifiers offering excellent musicality. What Makes The Difference A compact and versatile amplifier Optimised heat dissipation Extremely versatile Remarkable power/performance/price ratio Extremely Versatile Thanks to its 4x120 Watts RMS at 4 Ohms and its compact chassis barely bigger than half a page of A4 paper, the FPX 4.800 is an ideal solution for a wide range of uses. In bridged mode, it delivers 2x370 Watts RMS at 4 Ohms, enabling it to power a significant subwoofer channel with channels 3 and 4. It is also stable at 2 Ohms (4x185 Watts RMS) so it can also be used for powering different types of speaker drivers. In order to perfectly power the speaker drivers, each pair of channels is equipped with an adjustable active crossover from 50 to 500 Hz: high-pass, low-pass or wideband. Channels 3 & 4 are equipped with bass correction. The 2-/4-channel input modes ensure compatibility with mid-range head units only equipped with a pair output lines.
The FDS 4.350 is the 4-channel model (4 x 58 Watts RMS) and the most versatile of the range. It can operate in 4-, 3- or 2-channel mode. In most cases, it will be used to amplify a car’s front and rear speaker drivers. It can also be used to drive front speaker drivers and a small subwoofer, for a small installation which stays simple and integrated.
The FDS 1.350 is a mono block amplifier specifically designed for handling a subwoofer channel. It has a power of 210 and 350 Watts RMS under 4 and 2 Ohms respectively. In order to configure the system’s bass according to the car’s installation; it is equipped with an active crossover, bass correction and phase adjustment.
FSP-8 is the ultimate digital tool to optimise and shape the audio signal... High-resolution sound quality, compatible inputs/outputs, a user interface designed for and by acoustic experts, FSP-8 is the ultimate tool for the most demanding installations.How could we create the best product on the market for connecting your head unit to your amplifier system? How could we make it possible for you to shape and fine-tune the audio spectrum to create your very own musical experience?Even if most vehicles today are equipped with a standard audio system, the most demanding sound enthusiasts want unique, high-quality audio for their car.They want to build their system, step by step and have full control over each element of the audio story. The DSP (Digital Signal Processor) is an essential tool in achieving this.Features:High-resolution digital compatibility via optical inputs.Recall of stored presets and main settings management through the remote control (sold separately).FSP-8 DSP MANAGER: User-friendly interface for maximum efficiency when sculpting “Your Focal Sound” Specifications:Selectable high/low-level inputs for compatibility with factory or after-market head unitsHigh-resolution digital input (24 bits/192kHz)Auxiliary stereo inputRemote control with LED screen (sold separately)Dimensions (WxLxH): 57/16"x89/16"x17/8" (13.8cmx21.8cmx4.8cm)
The AP-4340 4-channel class AB amplifier can be used in three modes: 4, 3 or 2-channel. In 4-channel mode, its CEA power of 4 x 70W RMS will allow you to get the most from your Auditor kits installed up front and in the rear. The 3-channel mode enables you connect a kit to channels one and two, as well as an Auditor subwoofer to channels three and four in bridged mode for a CEA power of 190W RMS under 2 Ohms. The 2-channel mode, which consists of bridging channels 1-2 and 3-4, provides a CEA power of 2 x 190W RMS under 2 Ohms. Equipped with high-pass and low-pass crossovers, as well as a subsonic crossover, the AP-4340 amplifier guarantees the optimal performance of the kits and subwoofers in this line. Specifications:4/3/2-channel A/B class amplifierRCA inputsCEA Power (4Ω): 4x70W RMSNom. power (2Ω): 4x95W RMSNom. power (bridged 4Ω): 2x190W RMSHigh-pass crossover (channel 1-2):60Hz – 1.2KHzHigh-pass crossover (channel 3-4):100Hz – 2.2KHzLow pass crossover: 50 - 250HzFull range modeBandwidth: 10Hz - 30KHzDimensions (LxHxl) :1325/64"x2"x91/4" (340x50x235mm)
The FPX 4.800 is a very compact 4-channel amplifier with a power of 4x120 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.800 is the most versatile model in this range. Thanks to its very high power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair output lines. The high power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line.Features:D class 4/3/2 Channel amplifierStable under 2 OhmsAudio Mos-Fets - Optimized efficiencyHigh performance compact heat dissipation chassisHigh power and current dynamic reserveSpecifications:D Class amplifier - 4/3/2 channelsCEA power (4 ohms): 4x120 WrmsMaximum power (2 ohms): 4x185WrmsMaximum power (bridged 4 ohms): 2x370WrmsBandwidth: 10Hz – 20KHzTotal harmonic distortion: 0.01%SNR (1W/A): >76dBAConfigurable filters High Pass / Low Pass : 50Hz-500HzBass boost: (0/12dB)Mirroring Mode: (4CH/2CH)Protections: Short circuit / low impedance /reversal of polarity / DC / power drop / heat protectionDimensions (LxHxW): 921 (237x132x5
5-channel FPX 5.1200 amplifier has a maximum power of 4 x 120 Watt + 1 x 720 Watt at 2 Ohms! The input selector (2/4/6 channels) duplicates channels, meaning there will always be 5 output channels, even if the head unit only has one or two stereo outputs.To perfectly tune the subwoofer to the rest of the installation, the bass channel has a low-pass active crossover, a bass equaliser, phase adjustment and a subsonic filter (particularly useful for cutting off frequencies which are too low for a small subwoofer). The remote control enables you to adjust the bass level from the driving seat depending on the type of music you’re listening to.Stable at 4 and 2 Ohms, this new FPX amplifier will drive most speaker drivers on the market with just the right amount of power: 4 x 75 Watts + 1 x 420 Watts RMS at 4 Ohms (CEA standard). With its power and contained volume, FPX 5.1200 makes the installation easier in order to make the most of your boot space.Specifications:Only one amplifier for the entire hi-fi installationEasier to integrate and installCompact designSubstantial power and great musicalityExtremely versatileA dedicated subwoofer channel (+ remote control)Input selector (2/4/6 channels)Stable under 4 and 2 OhmsAdjustable active crossover for each pair of channelsDimensions: 13.25″ x 6.8″ x 2.25″ (337 x 175 x 57mm)
The FPX 4.400 is a very compact 4-channel amplifier with a power of 4x70 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.400 is the most “sound quality” model in this range. Thanks to its very comfortable power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair output lines. The power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line.Features:An audiophile and versatile amplifierOptimized heat dissipationExtremely versatileRemarkable power/performance/price ratioAB Class 4/3/2 Channels amplifier - Dedicated to sound qualityStable under 2 OhmsAudiophile Sanken® TransistorsHigh performance compact heat dissipation chassisHigh power and current dynamic reserveSpecifications:4-/3-/2-channel Class ABD amplifier2-/4-channel input modesStable at 2 OhmsActive crossover for each pair of channelsThe FPX 4.400 measures 314x175x57mm)CEA power (4 ohms) 4x70 Watts RMS Max. power (2 ohms) 4x100 Watts RMS Max. power (4 ohms bridged) 2x200 Watts RMS Bandwidth (-3dB) 10Hz – 22KHz THD 0.04% Crosstalk (1 KHz) > 54dB SNR (1W/A) > 77dBA
The FD 4.350 is the 4-channel model (4 x 58 Watts RMS) and the most versatile of the range. It can operate in 4-, 3- or 2-channel mode. In most cases, it will be used to amplify a car’s front and rear speaker drivers. It can also be used to drive front speaker drivers and a small subwoofer, for a small installation which stays simple and integrated.Features:D Class Amplifier – Direct Fet ® Technology – Thermal efficiency and precisionLow noise operational amplifiers : New Japan Radio ® NJM4580Low ESR capacitors - 105°cPseudo symmetrical inputsHigh level inputs through audio transformersSpecifications:4/3/2-channel D Class amplifierHigh-level inputs with auto-detect / RCAlow-level inputsCEA power (4 Ohms): 4x58 Watts RMSPower max (2 Ohms): 4x100 Watts RMSPower max (4 Ohms bridged): 2x200 Watts RMSConfigurable high-pass/low-pass crossover: 40Hz-400HzFull range modeProtections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / heat protectionDimensions (L x H x W):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85 kg
The FD 2.350 is a 2-channel model delivering a power of 2 x 105 Watts RMS under 4 Ohms. For a perfect matching, it’s featuring an active high-pass and lowpass crossover. The FD 2.350 can consequently drive a pair of speaker drivers or a subwoofer.Features:D Class – Direct Fet ® Technology - Efficient heat dissipation and precisionStable under 2 OhmsStackable aluminium chassis with high heat dissipationLow noise operational amplifiers New Japan Radio® NJM4580Low ESR capacitors - 105°C (220°F)Pseudo-balanced inputsCable accessories included - easy to install Specifications:Stereo D Class bridgeable amplifierHigh-level inputs with auto-detect / RCAlow-level inputsCEA power (4 Ohms): 2x105 Watts RMSPower max (2 Ohms): 2x170 Watts RMSPower max (4 Ohms bridged): 1x360 Watts RMSConfigurable high-pass/low-pass crossover: 40Hz-400HzFull range modeBass boost (0-12dB)Protections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / over heating protectionDimensions (LxHxW):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85kg
The FD 1.350 is a mono block amplifier specifically designed for handling a subwoofer channel. It has a power of 210 and 350 Watts RMS under 4 and 2 Ohms respectively. In order to configure the system’s bass according to the car’s installation; it is equipped with an active crossover, bass correction and phase adjustment.Features:D Class Amplifier – Direct Fet ® Technology – Thermal efficiency and precisionLow noise operational amplifiers : New Japan Radio ® NJM4580Low ESR capacitors - 105°cPseudo symmetrical inputsHigh level inputs through audio transformersSpecifications:Mono D Class amplifier with dual outputHigh-level inputs with auto-detection /RCA low-level inputsCEA power (4 Ohms): 1x210 Watts RMSPower max (2 Ohms): 1x350 Watts RMSLow-pass crossover: 40Hz-400HzProgressive phase adjustment (0-180°)Bass boost (0/6dB/12dB)Protections: Short circuit / low impedance / reversal ofpolarity / DC / power drop / heat protectionDimensions (LxHxW):713/16x41/4x111/16 (199x108x43mm)Weight: 0.85kg
Give your head unit a breath of fresh air. Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. It will give your installation a boost without you having to embark on a difficult installation process. Semi “Plug&Play”, Impulse 4.320 is a miniature 4-channel digital amplifier delivering 4 x 55 Watts. Impulse 4.320 is the perfect complement for your Focal Integration speaker drivers.Features:Ultra-compact – Easy to installCompatible with all head units (OEM and after-market)Automatic start-up with your original head unitISO compatible via cable accessories sold separatelySpecifications:CEA power (4 Ohms): 4x55WrmsPower max (2 Ohms): 4x80WrmsPower bridged (4 Ohms): 2x160WrmsBandwidth: 10Hz / 20KHzMinimum THD: 0.02%SNR: 80dBAWeight: 1.2lbsDimensions: 67/8x25/8x17/8" (175x66.5x47mm)