Turntable Cartridges

Disc Jockey Two HundredThe Prestige model DJ200 uses a modified four piece OTL cantilever technology, oxygen free wire in the coils and a specially designed, high polished, diamond mounted in a brass bushing.

Mellow YellowBoth the Silver3 and Gold3 use a four piece OTL cantilever with a Grado specific elliptical diamond stylus mounted on a brass bushing. With the Silver3 and Gold3, a machined turned generator is used to achieve a lower distortion and greater transparency. The Gold3 are hand selected from Silver3 production runs which meet higher test specifications. Approximately 5% of the run usually exhibits these specs and become a Gold3.Grado’s OTL, or optimized transmission line, technology provides an ideal transfer of signal from the surface of the LP to the generator of the system.This technology rejects unwanted resonances and lowers distortion preserving the fundamental and harmonic frequencies of the music. This also helps keep noise generated by the motor system in the cartridge to a minimum.Grado’s OTL stylus/cantilever design makes records sound quieter, improves the height, width, and depth of the soundstage, and present more detail than previously obtainable.The Silver3 & Gold3 are all hand assembled by our team in Brooklyn, with some builders having over 25 years of experience. With the recent development of the highly received Lineage Series of cartridges, we were able to have a trickle down of technology and bring a new technique to the Silver3 & Gold3. This updated series of cartridges offers excellent tonal balance, dynamics, and realism, for a most rewarding reproduction of vocals and instruments. Our coil winding techniques, using ultra high purity copper wire which were honed during the development of the Lineage Series, have let the electrical circuits achieve unison between the four coils in each phono cartridge. This allows for a precise balance between channels and accurate stereo imaging.As in all Grado phono cartridges the Silver3 & Gold3 are powered by a twin magnet system that optimizes the balance between stereo channels. All internal magnetic circuit parts are held to extremely high tolerances creating the desired stereo imaging. Grado’s patented Flux-Bridger design allows the Silver3 & Gold3 to have one of the lowest effective moving mass generating systems while creating an excellent balance throughout the full frequency range.The development of the Epoch in the Lineage Series gave us an in-depth experience with using an outer housing as a damping device. This led to the creation of a process which de-stresses the chassis and dissipates unwanted energy & resonant frequencies, allowing the desired signal to travel freely.

Mellow YellowBoth the Silver3 and Gold3 use a four piece OTL cantilever with a Grado specific elliptical diamond stylus mounted on a brass bushing. With the Silver3 and Gold3, a machined turned generator is used to achieve a lower distortion and greater transparency. The Gold3 are hand selected from Silver3 production runs which meet higher test specifications. Approximately 5% of the run usually exhibits these specs and become a Gold3.Grado’s OTL, or optimized transmission line, technology provides an ideal transfer of signal from the surface of the LP to the generator of the system.This technology rejects unwanted resonances and lowers distortion preserving the fundamental and harmonic frequencies of the music. This also helps keep noise generated by the motor system in the cartridge to a minimum.Grado’s OTL stylus/cantilever design makes records sound quieter, improves the height, width, and depth of the soundstage, and present more detail than previously obtainable.The Silver3 & Gold3 are all hand assembled by our team in Brooklyn, with some builders having over 25 years of experience. With the recent development of the highly received Lineage Series of cartridges, we were able to have a trickle down of technology and bring a new technique to the Silver3 & Gold3. This updated series of cartridges offers excellent tonal balance, dynamics, and realism, for a most rewarding reproduction of vocals and instruments. Our coil winding techniques, using ultra high purity copper wire which were honed during the development of the Lineage Series, have let the electrical circuits achieve unison between the four coils in each phono cartridge. This allows for a precise balance between channels and accurate stereo imaging.As in all Grado phono cartridges the Silver3 & Gold3 are powered by a twin magnet system that optimizes the balance between stereo channels. All internal magnetic circuit parts are held to extremely high tolerances creating the desired stereo imaging. Grado’s patented Flux-Bridger design allows the Silver3 & Gold3 to have one of the lowest effective moving mass generating systems while creating an excellent balance throughout the full frequency range.The development of the Epoch in the Lineage Series gave us an in-depth experience with using an outer housing as a damping device. This led to the creation of a process which de-stresses the chassis and dissipates unwanted energy & resonant frequencies, allowing the desired signal to travel freely.

Color me awesomeBoth the Black3 and Green3 use a three piece OTL cantilever that has a Grado specific diamond mounted on a brass bushing. The Green3 are hand selected from Black3 production runs which meet higher test specifications. Approximately 15% of the run usually exhibits these specs and become a Green3.Grado’s OTL, or optimized transmission line, technology provides an ideal transfer of signal from the surface of the LP to the generator of the system. This technology rejects unwanted resonances and lowers distortion preserving the fundamental and harmonic frequencies of the music. This also helps keep noise generated by the motor system in the cartridge to a minimum.Grado’s OTL stylus/cantilever design makes records sound quieter, improves the height, width, and depth of the soundstage, and present more detail than previously obtainable.The Black3 & Green3 are all hand assembled by our team in Brooklyn, with some builders having over 25 years of experience. With the recent development of the highly received Lineage Series of cartridges, we were able to have a trickle down of technology and bring a new technique to the Black3 & Green3. This updated series of cartridges offers excellent tonal balance, dynamics, and realism, for a most rewarding reproduction of vocals and instruments. Our coil winding techniques, using ultra high purity copper wire which were honed during the development of the Lineage Series, have let the electrical circuits achieve unison between the four coils in each phono cartridge. This allows for a precise balance between channels and accurate stereo imaging.As in all Grado phono cartridges the Black3 & Green3 are powered by a twin magnet system that optimizes the balance between stereo channels. All internal magnetic circuit parts are held to extremely high tolerances creating the desired stereo imaging. Grado’s patented Flux-Bridger design allows the Black3 & Green3 to have one of the lowest effective moving mass generating systems while creating an excellent balance throughout the full frequency range.The development of the Epoch in the Lineage Series gave us an in-depth experience with using an outer housing as a damping device. This led to the creation of a process which de-stresses the chassis and dissipates unwanted energy & resonant frequencies, allowing the desired signal to travel freely.

Awesome sound in red states and blue statesBoth the Blue3 and Red3 use a four piece OTL cantilever that has a Grado specific diamond mounted on a brass bushing. The Red3 are hand selected from Blue3 production runs which meet higher test specifications. Approximately 10% of the run usually exhibits these specs and become a Red3.Grado’s OTL, or optimized transmission line, technology provides an ideal transfer of signal from the surface of the LP to the generator of the system. This technology rejects unwanted resonances and lowers distortion preserving the fundamental and harmonic frequencies of the music. This also helps keep noise generated by the motor system in the cartridge to a minimum.Grado’s OTL stylus/cantilever design makes records sound quieter, improves the height, width, and depth of the soundstage, and present more detail than previously obtainable.The Red3 & Blue3 are all hand assembled by our team in Brooklyn, with some builders having over 25 years of experience. With the recent development of the highly received Lineage Series of cartridges, we were able to have a trickle down of technology and bring a new technique to the Red3 & Blue3. This updated series of cartridges offers excellent tonal balance, dynamics, and realism, for a most rewarding reproduction of vocals and instruments. Our coil winding techniques, using ultra high purity copper wire which were honed during the development of the Lineage Series, have let the electrical circuits achieve unison between the four coils in each phono cartridge. This allows for a precise balance between channels and accurate stereo imaging.As in all Grado phono cartridges the Red3 & Blue3 are powered by a twin magnet system that optimizes the balance between stereo channels. All internal magnetic circuit parts are held to extremely high tolerances creating the desired stereo imaging. Grado’s patented Flux-Bridger design allows the Red3 & Blue3 to have one of the lowest effective moving mass generating systems while creating an excellent balance throughout the full frequency range.The development of the Epoch in the Lineage Series gave us an in-depth experience with using an outer housing as a damping device. This led to the creation of a process which de-stresses the chassis and dissipates unwanted energy & resonant frequencies, allowing the desired signal to travel freely.

For more than 35 years Dynavector have established an enviable reputation for producing affordable high quality moving coil cartridges. Notably high output models that are designed to work with MM inputs negating the necessity for equipment change or the use of setup devices required for low output cartridges. The outstanding performance of the Dynavector high output moving coil cartridges can be attributed to the exclusively Dynavector designed coil winding machine capable of utilizing extremely fine coil wire providing a high output to mass ratio.Features and ImprovementsDV-20X has a solid aluminum alloy body and a rigid magnet construction similar to XX-2MKII. The cantilever is a 6mm length of hard aluminum pipe with a Micro-Ridge stylus. The magnetic flux damping and softened magnetism along with powerful neodymium magnets. The 20 X2L has an output of 0.3 mV ideal for most MC phono stages. The low output version offers superb performance when combined with dedicated moving coil inputs.

For more than 35 years Dynavector have established an enviable reputation for producing affordable high quality moving coil cartridges. Notably high output models that are designed to work with MM inputs negating the necessity for equipment change or the use of setup devices required for low output cartridges. The outstanding performance of the Dynavector high output moving coil cartridges can be attributed to the exclusively Dynavector designed coil winding machine capable of utilizing extremely fine coil wire providing a high output to mass ratio.Features and ImprovementsDV-20X has a solid aluminum alloy body and a rigid magnet construction similar to XX-2MKII. The cantilever is a 6mm length of hard aluminum pipe with a Micro-Ridge stylus. The magnetic flux damping and softened magnetism along with powerful neodymium magnets gives the 20X2H a healthy 2.8 mV output - suitable for most MM inputs. The high output model is well suited to valve preamplifiers or electronics that only offer MM inputs.

The original Te Kaitora cartridge was the result of collaboration between Dynavector Japan and Dynavector New Zealand. The Te Kaitora allowed analogue enthusiasts to embark on a voyage of discovery to the outer limits of vinyl reproduction. The improved Te Kaitora Rua continues the journey by incorporating many of the newest features of its Dynavector stable-mates, the XV-1s and XX-2. The Te Kaitora Rua has even managed to improve on the original's silk-like treble and openness. Note: Te Kaitora means "The Discoverer" in the language of the NZ Maori people, Rua, is "the second version".ImprovementsThe wire for the coil has been changed to the PCOCC copper wire from the silver wire. It sounds a much smoother and has a much better musical performance.A titanium headpiece for maximum ridgity along with a miniature stainless steel bolt coupling the front and rear yokes to the magnetic circuit assembly.A 6mm long boron cantilever with the Pathfinder (PF) line contact stylus as used with both Dynavector XV-1s and XX-2.The ingenious square shaped armature and matching square shaped aperture in the front yoke providing much improved linearity in the magnetic flux distribution.Alnico magnets are used for high magnetic flux density.

The DV XX-1 was the first cartridge to feature a "magnetic flux damper" (patent) and softened magnetism" (patent) processes that reject the magnetic fluctuation that is detrimental to a moving coil cartridges performance.The The DV XX-2 MKII retains the benefit of the flux damper but features the Alnico-5 magnet and the similar rigid construction to the Te Kaitora Rua. Alnico magnets exhibit high magnetic flux density combining with a low coercive therefore magnetic resistance is lower than other magnetic types such as rare earth and ferrite, providing the exceptional stability of the XX-2 MKII output voltage. There is also the additional advantage of low magnetic and electrical resistance contributing to a discernable improvement in sound quality.The XX-2MKII also exhibits deep powerful bass, treble is both clear and lively possessing none of the hardness found in many moving coil designs.The XX-2MKII also features a 6 mm solid boron cantilever fitted with a Pathfinder Line contact stylus. PCOCC (pure copper ohno continuous casting process) copper wire is used for the coil. The output voltage of 0.28mV is higher than that of the XX-2 and 6 ohms impedance are suited to most moving coil phono stages.For ridgity of construction the XX-2 MKII cartridge body is machined from 7075 aluminium the hardest available. However, having only a total weight of only 8.9 grams it is suitable for a variety of popular tonearms.

The HANA-Umami WayThe HANA-Umami Red high-end moving coil cartridge combines brilliant materials and classic Japanese techniques with modern audio engineering. Ebony wood, rare-earth magnets, precision-cut diamond, high-purity copper wires, Urushi lacquering, and CNC machined Duralumin synergize under the vision of Hana designer Okada-san.The synergistic relationship in MC generators between magnet, armature, and coil windings is a critical aspect of outstanding cartridge design; and like a signature dish at a Michelin 3-star restaurant, every element and detail working in concert results in a memorable and emotional experience.All the major parts in a HANA-Umami Red are manufactured in house by Excel Sound with its rich history spanning over 50 years. Excel’s highly trained craftsmen skillfully hand assemble the HANA-Umami Red ensuring an intensely musical experience furthering the HANA “Brilliant and Gorgeous” sound quality.Umami Sound - Wonderful Taste in Music

One of the world’s best High Output Moving Coil cartridges, the MH combines the technological advances of the Hana M Series with the optimal interface for moving magnet phono stages.M Series Nude Microline stylus – Higher Specification Part Befitting its name, the M Series uses a Nude Microline stylus, mimicking the cutting stylus and fitting more precisely into the vinyl groove. This enhances tracking to capture the most delicate musical details with better frequency reproduction, stereo imaging, and resolution. Delrin© cartridge body – Advanced Materials The M Series cartridge body is injection molded from Delrin©, a high-tech polymer with improved mechanical characteristics for better resonance damping, to reveal more low level information and enhance dynamic range. Cryogenic Processing - Unique Technical Treatment Cryogenic processing is Cold Annealing at near absolute zero temperature that restructures metals at the molecular level, especially important in the Alnico based magnetic electro-motive circuit (cartridge signal generator). The M Series parts treated include the front yoke as well as center and rear components. The result is a more precise and controlled magnetic flux field for greater linearity and musical sound quality. Brass Cap with Threaded fittings - Superior Mechanical Interface The Delrin© cartridge body features an integral machined brass cap providing constrained mode layer damping and its heavier 9.5 gram weight provides expanded compatibility with a wider range of tonearms and turntables. Built into the M Series Delrin© cartridge body are metal threaded fittings for headshell mounting hardware, offering easier attachment and a superior mechanical interface for better bass and dynamics.

Building upon the foundation of the critically acclaimed HANA sound, the ML aspires toward affordable perfection and represent the further evolution of the “Brilliant and Gorgeous” quality that has earned HANA its worldwide reputation.M Series Nude Microline stylus – Higher Specification Part Befitting its name, the M Series uses a Nude Microline stylus, mimicking the cutting stylus and fitting more precisely into the vinyl groove. This enhances tracking to capture the most delicate musical details with better frequency reproduction, stereo imaging, and resolution.High Purity copper wire – Higher Specification Part Very high-purity copper wire is used for winding the ML coil with a new low impedance generator for optimized performance with a broader range of phono preampsDelrin© cartridge body – Advanced Materials The M Series cartridge body is injection molded from Delrin©, a high-tech polymer with improved mechanical characteristics for better resonance damping, to reveal more low level information and enhance dynamic range.Cryogenic Processing - Unique Technical Treatment Cryogenic processing is Cold Annealing at near absolute zero temperature that restructures metals at the molecular level, especially important in the Alnico based magnetic electro-motive circuit (cartridge signal generator). The M Series parts treated include the front yoke as well as center and rear components. The result is a more precise and controlled magnetic flux field for greater linearity and musical sound quality.Brass Cap with Threaded fittings - Superior Mechanical Interface The Delrin© cartridge body features an integral machined brass cap providing constrained mode layer damping and its heavier 9.5 gram weight provides expanded compatibility with a wider range of tonearms and turntables.Built into the M Series Delrin© cartridge body are metal threaded fittings for headshell mounting hardware, offering easier attachment and a superior mechanical interface for better bass and dynamics.

The Hana SH combines high output with high resolution, courtesy of its special coil design and Shibata stylus. Compatible with standard MM phono stages, a high-output MC provides dynamics, drive, and excellent stereo imaging. With over 50 years of experience in cartridge design and manufacture, Excel Sound builds many of the most highly regarded high-output MC cartridges.  

The Hana EH high-output moving coil cartridge represents the best way to upgrade from “starter” MM cartridges that typically come packaged with most entry-level turntables. Weighing in at only 5 grams, and possessing great tracking ability, the Hana EH cartridge’s distinctive moss green body houses a special cross-coil generator, reproducing great bass and dynamics. The elliptical stylus mounted to an aluminum cantilever easily extracts the music in the groove as it effortlessly traces you LPs.The EH is plug-and-play compatible with MM phono stages found in integrated amplifiers and AV receivers. 

The Hana EL provides high-end musical performance from a low-output moving coil cartridge at an extremely attractive price. Handmade in Japan, the EL uses ALNICO magnets and affords the listener the textural, imaging, and musically involving qualities associated with the best MC cartridges.Long prized by audiophiles and music lovers, affordable low output MCs such as the EL are a perfect match to today’s generation of high-gain phono stages.

The Ania with a stylus from the AphetaThe Rega Ania Pro is a moving coil cartridge that keeps the rigid body and hand-wound generator of the Ania but upgrades the most critical detail: the stylus. Here Rega uses a nude diamond with a Vital profile, the stylus philosophy inherited from the Apheta range, to recover as much information from the groove as possible. It is easy to recognise by its red protective cover.Sound characterRega sums up its sound in three phrases: tight bass, warm mids and accurate highs. The result is balanced and detailed, with wide dynamic range, a spacious soundstage and natural tonal balance. Reviewers at Hi-Fi Choice and The Ear described it as a clear step up from the Ania, especially on Rega turntables.Which turntables it is made forRega recommends the Ania Pro as the ideal cartridge for the Planar 6 and Planar 8, and offers versions of both turntables with the cartridge factory-fitted. It also suits the Planar 3 and any Rega tonearm with three-point fixing, such as the RB330 and RB880. It needs a phono stage with an MC input.

Practically new with 20-25 hours of use!! The MC Anna Diamond model represents the highest echelon of Moving Coil cartridges. As its name suggests, the MC Anna Diamond uses a Diamond cantilever that in combination with Ortofon Replicant 100 diamond offers extreme transparency, speed and responsiveness beyond that of any other combination. This state of the art product, representative of numerous Ortofon design elements and ideas, is truly exemplary of the highest degree of performance possible in contemporary analogue playback technology.

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables. The E3 cartridge, representing the top of the range features the same aluminium cantilever as the E2, but benefits from a superior, bonded, super-elliptical (0.3 x 0.7 mil) stylus. This gives it better high frequency detail retrieval over ordinary elliptical (0.4 x 0.7 mil) or spherical (0.6 mil) types due to its smaller front-to-back radius. The main effect is the reduction of sibilance, especially in high level vocal recordings Magnetic Duplex Technology™ All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage. Expert Adjustment The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product. Stylus/Cantilever Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

The Goldring philosophy is to promote the accurate replication of the original record production, maintaining the creative nuances, musicality and rhythm the artist intended you to hear. With the versatile E Series, this is easy to achieve; each is designed to be simple to fit to the majority of budget to medium priced turntables. The E2 cartridge, the middle in the range, features the same spherical stylus profile as the E1 but with the additional benefit of an upgraded aluminium cantilever. This is both stiff and light weight allowing the stylus to more accurately trace medium to high frequencies offering more detail and reducing distortion and mis-tracking during loud passages. Magnetic Duplex Technology™ All cartridges in the range feature Magnetic Duplex Technology™-a 'dual magnet' generator assembly with an identical geometry to that of the original cutting head. This means it can more accurately reproduce the stereo information in the record groove, providing better channel separation and a more involving and musical sound stage. Expert Adjustment The E-series cartridges have been designed to allow micro-adjustments to be made during production using a special adjustment screw. This means the cartridge can be safely installed in a typical turntable because the angle that the stylus makes with the record surface has been pre-set. The result is an optimised channel balance with zero degrees of horizontal tracking adjustment required. This ensures a consistent and reassuring performance for the life of the product. Stylus/Cantilever Featuring spherical styli with a choice of cantilevers, the E1 and E2 models are ideal as an upgrade to any budget, pre-fitted or obsolete cartridge. The E3 model with its re­fined super elliptical stylus is a worthwhile upgrade for those wishing to squeeze even more information and detail from the record groove.

Fourth generation, top of the rangeThe Rega Aphelion 2 is the fourth generation of the British company's hand-built moving coil cartridges and its reference model. It builds on the original Aphelion and the Apheta 3, but Rega's engineers re-examined and refined every individual element. Rega itself describes it as the best-performing cartridge it has made to date.Sound characterIts presentation is musical and natural, with rich timbres, transparency and balance. The frequency ranges knit together without exaggeration, detail is exceptional and bass is well articulated and defined, within a natural, convincing soundstage. Jason Kennedy of The Ear described it as a revelation, precisely because it shows what records really sound like.For reference systemsThe Aphelion 2 was designed for Rega's reference turntables, such as the Planar 10 and the Naia, and for the RB3000 tonearm. Rega recommends the Aura MC phono stage and the Aethos and Osiris amplifiers as partners. It is available to special order.

The MC cartridge that makes the upgrade affordableThe Rega Ania is the moving coil (MC) cartridge with which the British company brought the know-how of the Apheta and Aphelion to a far more accessible level. It uses the same hand-wound micro coil as the rest of Rega's MC range, an elliptical diamond stylus and an aluminium cantilever. For anyone already running a Rega turntable with a moving magnet cartridge, it is the most logical next step towards more detail, speed and clarity.Sound characterThe Ania delivers lively dynamics and natural tonality, with good resolution of the small details hidden in the groove. Bass is tight and controlled, the midrange has body and the treble stays clean without harshness. It rewards both focused listening and everyday use, without needing an exotic system to show what it can do.Ideal pairingsRega recommends the Ania for the Planar 3 and Planar 6, with which it shares the philosophy of light, rigid construction. It fits equally well on any Rega tonearm with three-point fixing (RB330, RB880, RB3000). As with every true MC cartridge its output is low, so it needs a phono stage with an MC input and enough gain, such as the Rega Fono MC.

Genuine Denon replacement stylus for Denon MM turntable cartridges. Replacing the stylus in time keeps sound quality high and protects your records from wear.The role of the stylusThe stylus is the only point of contact between the turntable and the record. Its condition determines how faithfully the information cut into the groove is conveyed, and how well your records are preserved over the years. That is why replacing it in good time is one of the simplest and most effective care steps for any vinyl system.Small part, big responsibilityThe stylus tip moves within the groove and turns its tiny modulations into motion, which the cartridge converts into an electrical signal. Any deviation in the shape of the tip directly affects sound quality.Normal wearLike any part that works through friction, the stylus wears gradually with use. Wear is slow and often not noticed straight away, so its condition is worth checking at regular intervals.Replacement without changing the cartridgeIn moving magnet (MM) cartridges, such as those supplied with many Denon turntables, the stylus is a separate, removable part. You can renew the most delicate part of the cartridge without changing the whole cartridge and without re-adjusting the tonearm.Why genuine mattersA genuine Denon spare part is designed for the specific cartridge body, so it fits correctly and preserves the sound the manufacturer intended. Correct fit also ensures the tip sits in the right position within the groove, avoiding needless wear on your records.When to replace itThere is no single number of hours that applies to everyone, as stylus wear depends on how often you listen, how clean your records are and how well the turntable is set up. There are, however, clear signs that it is time for a new one, as well as simple habits that extend its life. Paying attention to them protects your collection.Audible signsIf the sound becomes dull or veiled, the treble loses its sparkle, or distortion appears in loud passages and on vocals, especially towards the end of a side, the stylus has most likely worn.Mechanical signsA stylus that skips grooves, slides across the record, or looks bent or crooked when viewed up close needs replacing immediately. Continued use can cause permanent damage to the grooves, which no new stylus can undo.Proper careClean the stylus regularly with a soft brush designed for the purpose, always moving it from back to front, and keep your records free of dust. Fit the stylus guard whenever you move or clean the turntable, when accidental knocks are most likely.Regular checksAn occasional check with a magnifying glass, or by your technician, helps spot wear early. It is a good idea to keep a spare stylus on hand, so listening is not interrupted when the time comes to change it. A worn stylus costs far less than a damaged record.Choosing and fittingDenon offers different replacement styli, each designed for a specific cartridge body. Choosing the correct code is the most important step. Once you have the right part, fitting is a simple process that takes a few minutes, needs no tools and restores your turntable's sound quality to how it was on the first day.Find the correct codeThe replacement stylus code is listed in the specifications and owner's manual of your turntable or cartridge. Compare it with the product code before buying. If in doubt, our team can help you confirm compatibility.Removing the old stylusBefore you start, lock the tonearm in its rest and switch the turntable off. Then gently pull the old stylus assembly forwards, without putting pressure on the cartridge body.Fitting the new oneSlide the new stylus into place, holding it by its plastic body, until it is fully seated. Then check the tracking force according to the manufacturer's instructions, so it reads the groove correctly and wears evenly. Finally, give the new tip a gentle clean before playing your first record.Ready to listenWith a new stylus, detail and clarity return and your records are protected. Make a note of the date you changed it, so you know when the next check is due, and keep the stylus guard fitted whenever the turntable is not in use.

Genuine Denon replacement stylus for Denon MM turntable cartridges. Replacing the stylus in time keeps sound quality high and protects your records from wear.The role of the stylusThe stylus is the only point of contact between the turntable and the record. Its condition determines how faithfully the information cut into the groove is conveyed, and how well your records are preserved over the years. That is why replacing it in good time is one of the simplest and most effective care steps for any vinyl system.Small part, big responsibilityThe stylus tip moves within the groove and turns its tiny modulations into motion, which the cartridge converts into an electrical signal. Any deviation in the shape of the tip directly affects sound quality.Normal wearLike any part that works through friction, the stylus wears gradually with use. Wear is slow and often not noticed straight away, so its condition is worth checking at regular intervals.Replacement without changing the cartridgeIn moving magnet (MM) cartridges, such as those supplied with many Denon turntables, the stylus is a separate, removable part. You can renew the most delicate part of the cartridge without changing the whole cartridge and without re-adjusting the tonearm.Why genuine mattersA genuine Denon spare part is designed for the specific cartridge body, so it fits correctly and preserves the sound the manufacturer intended. Correct fit also ensures the tip sits in the right position within the groove, avoiding needless wear on your records.When to replace itThere is no single number of hours that applies to everyone, as stylus wear depends on how often you listen, how clean your records are and how well the turntable is set up. There are, however, clear signs that it is time for a new one, as well as simple habits that extend its life. Paying attention to them protects your collection.Audible signsIf the sound becomes dull or veiled, the treble loses its sparkle, or distortion appears in loud passages and on vocals, especially towards the end of a side, the stylus has most likely worn.Mechanical signsA stylus that skips grooves, slides across the record, or looks bent or crooked when viewed up close needs replacing immediately. Continued use can cause permanent damage to the grooves, which no new stylus can undo.Proper careClean the stylus regularly with a soft brush designed for the purpose, always moving it from back to front, and keep your records free of dust. Fit the stylus guard whenever you move or clean the turntable, when accidental knocks are most likely.Regular checksAn occasional check with a magnifying glass, or by your technician, helps spot wear early. It is a good idea to keep a spare stylus on hand, so listening is not interrupted when the time comes to change it. A worn stylus costs far less than a damaged record.Choosing and fittingDenon offers different replacement styli, each designed for a specific cartridge body. Choosing the correct code is the most important step. Once you have the right part, fitting is a simple process that takes a few minutes, needs no tools and restores your turntable's sound quality to how it was on the first day.Find the correct codeThe replacement stylus code is listed in the specifications and owner's manual of your turntable or cartridge. Compare it with the product code before buying. If in doubt, our team can help you confirm compatibility.Removing the old stylusBefore you start, lock the tonearm in its rest and switch the turntable off. Then gently pull the old stylus assembly forwards, without putting pressure on the cartridge body.Fitting the new oneSlide the new stylus into place, holding it by its plastic body, until it is fully seated. Then check the tracking force according to the manufacturer's instructions, so it reads the groove correctly and wears evenly. Finally, give the new tip a gentle clean before playing your first record.Ready to listenWith a new stylus, detail and clarity return and your records are protected. Make a note of the date you changed it, so you know when the next check is due, and keep the stylus guard fitted whenever the turntable is not in use.

The THORENS TAS 1600 is an MC pickup manufactured for THORENS in Japan. The aim of the development was the optimal combination of the pick-up in combination with the TD 1600/1601 turntable and the TP 92 precision tonearm. With an output voltage of 0.6mV (5.5cm/sec) and 12 ohms internal resistance, the pick-up harmonises with all common phono preamplifiers. A naked diamond with line contact cut in combination with a solid boron cantilver guarantee best pickup capability and sound quality.

The AT-ART1000 (“ART” for Audio-Technica Reference Transducer) is Audio-Technica’s new flagship phono cartridge, handmade in Japan. Born of the pursuit of audio excellence that has driven A-T for more than 50 years, the AT-ART1000 introduces an innovative, audiophile design heretofore unseen in mass-produced cartridges. The cartridge’s direct power system places the dual moving coil directly on top of the stylus tip, ensuring that the audio quality does not suffer the negative effects normally introduced by the cantilever's length and material type. Having the coils move in such close proximity to the stylus tip allows the cartridge to vividly render even the most subtle sonic details and provide unsurpassed transient response. Each of the cartridge’s two coils is constructed of 20 ìm diameter PCOCC (Pure Copper by Ohno Continuous Casting) wire, wound eight turns to a diameter of 0.9 mm to create a non-magnetic core coil. The 3-ohm coils are placed in the tiny 0.6 mm gap of a powerful magnetic circuit, enabling each coil to generate an output voltage of 0.2 mV. The AT-ART1000 features the same high-performance line contact stylus and solid boron cantilever found in the AT-OC9/III, enabling the cartridge to faithfully trace the record groove and reliably transfer the signal to the coils. The base that supports the specialized magnetic circuit and vibration system is made from titanium. This sturdy base is instrumental in providing consistent playback, and works in combination with the cartridge’s hard plastic cover and aluminum housing to disperse resonance that negatively affects the sound quality. *The AT-ART1000’s stylus assembly is not field-replaceable, but Audio-Technica offers a fee-based Cartridge Rebuild Program. Under this program, Audio-Technica will replace all assembly parts, including the stylus tip, cantilever, coils, and rubber dampers.

An update of the AT-ART7, the AT-ART9XA non-magnetic core MC cartridge features a Shibata stylus on a 0.28 mm diameter solid boron cantilever. The “ART” in the model number stands for Audio-Technica Reference Transducer, a designation that we give only to our flagship phono cartridges. Compared with the magnetic core used in most MC cartridges, non-magnetic core cartridges are free from magnetic distortion, allowing for natural timbre and a precise sound field. Although conventional non-magnetic cores struggle with output voltage, the AT-ART9XA features a newly designed coil armature with an improved output voltage of 0.2 mV (1 kHz, 5 cm/sec). The dual moving coils (fashioned from high-performance PCOCC wire) are aligned in an inverted V shape to provide high separation and wide response. Threaded cartridge mounting holes make installation to a headshell or integrated tonearm incredibly easy.

Featuring a special line contact stylus on a 0.28 mm diameter solid boron cantilever, the AT-ART9XI replaces the AT-ART9 as Audio-Technica’s flagship magnetic core MC cartridge. The “ART” in the model number stands for Audio-Technica Reference Transducer, a designation that we give only to our flagship phono cartridges. The specially designed magnetic circuit boasts an output voltage of 0.5 mV (1 kHz, 5 cm/sec), making the cartridge easy to use and capable of reproducing even the most delicate expressions, while also ensuring dynamic playback. The dual moving coils (fashioned from high-performance PCOCC wire) are aligned in an inverted V shape to provide high separation and wide response for clear sound localization and minimal distortion. Threaded cartridge mounting holes make installation to a headshell or integrated tonearm incredibly easy.

With a specialized body and internal wiring dedicated to monaural sound reproduction, the VM610xMONO conical stylus cartridge is designed for playing mono records.  Part of the 600 Series in Audio-Technica’s new VM cartridge line – a line that harks back to A-T’s early days as a manufacturer primarily of high-end phono cartridges – the VM610xMONO is equipped with dual magnets that are internally connected to reduce record noise and obtain a highly focused “center” sound image that stereo cartridges can’t provide. Includes mounting hardware.

This VM95 Series cartridge with 3.0 mil conical stylus fits half-inch mount turntables. While this cartridge is designed to play 78 RPM mono records, it is, nevertheless, a stereo cartridge, allowing users to choose between the left and right channels, which can be especially helpful in archiving applications to minimize noise and distortion. The durable, low-resonance housing includes threaded inserts that enable the cartridge to be mounted to the headshell with just two screws – no nuts required. And since all VM95 Series share the same body, the stylus can be replaced with any of the six interchangeable AT-VMN95 replacement styli.

The AT-VM95SH, features a Nude Shibata stylus, one of the most acclaimed stylus format by high end audiophiles. The Shibata stylus produces mid and bass sounds strong and rich in addition to offer a frequency response up to 25,000 Hz. Aluminium cantilever 3.5mV output voltage Compatible body with all VM95 Series stylus assemblies 20 to 25,000Hz frequency response VM95 Series - Styli compatibility Every cartridge diamond stylus becomes worn after a period of play. Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus. Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus. The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible. AT-VMN95C, AT-VMN95E, AT-VMN95EN, AT-VMN95ML, AT-VMN95SH, AT-VMN95SP AT-VM9E Series compatibility with the AT-XP Series DJ Cartridges The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers. VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers. Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli. The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing. The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction. ATN-XP7, ATN-XP5, ATN-XP3 Shibata Stylus Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume. No use of nuts VM95 Series cartridges features two M2.6 threaded inserts allowing the installation of the cartridge onto tonearm or removable headshell without the use of nuts.Each cartridge is provided with one pair of 8mm M2.6 screws, one pair of 11mm M2.6 screws and two plastic washers.

The Audio-Technica AT-VM95EN is a Dual Moving Magnet phono cartridge from the VM95 Series, with a 0.3 × 0.7 mil nude elliptical stylus and an aluminium pipe cantilever. The diamond is a single solid piece (nude) mounted directly in the cantilever, for a lighter and stiffer transmission than the bonded tip of the AT-VM95E, with a clear difference in high-frequency detail and transients.It fits any tonearm with a standard 1/2-inch headshell and, like every cartridge in the series, accepts any VM95 stylus, so you can upgrade the sound later by changing only the stylus.

The Audio-Technica AT-VM95C is a Dual Moving Magnet phono cartridge from the VM95 Series, with a 0.6 mil conical stylus and an aluminium pipe cantilever. It is the entry model of the series, successor to the legendary AT91 and AT91R, and the cartridge Audio-Technica fits to turntables such as the AT-LP70XBT.It fits any tonearm with a standard 1/2-inch headshell and, like every cartridge in the series, accepts any VM95 stylus, so you can upgrade the sound later by changing only the stylus.

For 78 rpm collectionsThe Rega RB78 is a hand-built mono moving magnet (MM) cartridge in a custom body that Rega designed specifically for playing 78 rpm records. It is a general-purpose cartridge for anyone who wants to hear historic shellac recordings properly and with the right tools, from jazz and blues to classical music and early folk recordings.Why a dedicated cartridge is needed78 rpm records are mono and are cut with a much wider groove than microgroove vinyl records. An ordinary stereo stylus sits too low in that groove and reads noise instead of music. The RB78 uses a stylus with a 78 profile and a mono generator, so that it rests on the right parts of the groove wall.Its natural partnerRega makes the Planar 78, a single-speed turntable dedicated to 78 rpm, and the RB78 is the dedicated cartridge it recommends for it; it is sold separately. Thanks to standard two-screw fixing, it can also be fitted to another turntable or to a second tonearm on a deck that supports 78 rpm.

Dual moving coil stereo cartridge with bonded Elliptical stylus AT-OC9XEB Dual moving coil stereo cartridge with bonded Elliptical stylus, Features a bonded Elliptical stylus and aluminium cantilever and A neodymium magnet and pure iron yoke provide increased magnetic energy. The next Generation of the legendary OC9 cartridge series Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. An excellent affordable introduction to the characteristics that is moving coil. Features bonded Elliptical stylus and aluminium cantilever A neodymium magnet and pure iron yoke provides increased magnetic energy Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve the purest signal possible Elliptical Bonded Stylus Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion. Easy mounting Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required. Aluminium Body Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction.

Dual moving coil stereo cartridge with Microlinear stylus AT-OC9XML Dual moving coil stereo cartridge with Microlinear stylus - Features nude Microlinear stylus and boron cantilever , Neodymium magnet and permendur yoke for increased magnetic energy and Features threaded inserts in the cartridge body The next Generation of the legendary OC9 cartridge series Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. Microlinear complex diamond profile enabling higher frequency response, detail like never before experienced and limiting inner groove distortion. Microlinear diamond profile provides low record and stylus wear. Features nude Microlinear stylus and boron cantilever which provides lower distortion and high transient response A neodymium magnet and permendur yoke provides dramatically increased magnetic energy Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required  Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer  Microlinear Stylus Microlinear diamond profile offers high frequency response with less wear and distortion than elliptical or conventional linear contact styli. Easy mounting Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required. Aluminium Body Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction

Dual moving coil stereo cartridge with Elliptical nude stylus AT-OC9XEN Dual moving coil stereo cartridge with Elliptical nude stylus - Features low mass nude elliptical stylus and aluminium cantilever, A neodymium magnet and pure iron yoke provide increased magnetic energy and Features threaded inserts in the cartr. The next Generation of the legendary OC9 cartridge series Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. Featuring a square shank for accurate stylus alignment and nude diamond for increased fine detail retrieval. Features low mass nude elliptical stylus and aluminium cantilever A neodymium magnet and pure iron yoke provide increased magnetic energy Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required  Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve the purest signal possible Elliptical Nude Stylus Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion. Easy mounting Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required. Aluminium Body Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction.

Dual moving coil stereo cartridge with Shibata stylus AT-OC9XSH Dual moving coil stereo cartridge with Shibata stylus - Features a Nude Shibata stylus and boron cantilever , Neodymium magnet and permendur yoke for increased magnetic energy and Features threaded inserts in the cartridge body The next Generation of the legendary OC9 cartridge series Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. Shibata profile diamond originally design for Quadraphonic replay offers a depth of sound, combined with high frequency response that has to be heard to be believed. Features nude Shibata stylus and boron cantilever with rich low frequency reproduction and high transient response A neodymium magnet and permendur yoke provides dramatically increased magnetic energy Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required  Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer  Shibata Stylus Provides a beautiful mid-high range Shibata-signature sound and strong mid-range volume. Easy mounting Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required. Aluminium Body Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction

Dual moving coil stereo cartridge with Special Line Contact stylus AT-OC9XSL Dual moving coil stereo cartridge with Special Line Contact stylus - Features a Nude Special Line Contact stylus and boron cantilever , Neodymium magnet and permendur yoke for increased magnetic energy and Features threaded inserts in the cartri. The next Generation of the legendary OC9 cartridge series Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. Special Line Contact as featured in our flagship ART1000, this diamond profile offers the ultimate in accurate sonic reproduction with a sense of space and realism to all instruments that few other configuration can achieve. Features Nude Special Line Contact stylus and boron cantilever with accurate tracking ability and high transient response A neodymium magnet and permendur yoke provides dramatically increased magnetic energy Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required  Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer  Special Line Contact Stylus Special Line Contact diamond profile offers the ultimate in accurate sonic reproduction Easy mounting Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required. Aluminium Body Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction

The Audio-Technica AT85EP is a Dual Magnet phono cartridge with a P-mount (T4P) connector, designed for linear-tracking turntables from Technics, Hitachi, Pioneer and similar models. With a 0.3 × 0.7 mil elliptical stylus and an aluminium cantilever, it brings Audio-Technica’s clear sound to these turntables.Dual Magnet and para-toroidal coilsThe dual magnet construction is combined with para-toroidal coils for excellent clarity and good channel separation (20 dB at 1 kHz).Installation without adjustmentThe P-mount cartridge plugs straight into the tonearm and is secured with a single screw, with no geometry or tracking force adjustment. With the AT-PMA1 adapter it can also be fitted to a tonearm with a 1/2-inch headshell.

The Audio-Technica AT-VM95E is a Dual Moving Magnet phono cartridge from the VM95 Series, with a 0.3 × 0.7 mil elliptical stylus and an aluminium pipe cantilever. It succeeds the legendary AT95E and is one of the most popular upgrades from a turntable’s stock cartridge.It fits any tonearm with a standard 1/2-inch headshell and, like every cartridge in the series, accepts any VM95 stylus, so you can upgrade the sound later by changing only the stylus.

The VM510CB conical stylus cartridge is the entry-level 500 Series model in Audio-Technica’s new VM cartridge line – a line that harks back to A-T’s early days as a manufacturer primarily of high-end phono cartridges, while also incorporating today’s advanced technology. Like all VM cartridges, the VM510CB is equipped with dual magnets that are positioned to match the left and right channels in the stereo record groove for outstanding channel separation and extended frequency response. The cartridge’s 0.6 mil conical bonded stylus tracks the center of the record groove for reliable performance and excellent fidelity. Includes mounting hardware. Specifications:VM dual magnet cartridge with 0.6 mil conical stylusAluminum cantileverParatoroidal coils improve generating efficiencyCenter shield plate between the left and right channels reduces crosstalkDurable low-resonance polymer housingFrequency Response: 20-20,000 HzChannel Separation: 25 dB (1 kHz)Vertical Tracking Force: 1.8-2.2 g (2.0 g standard)Stylus Construction: Bonded round shankRecommended Load Impedance: 47,000 ohms

Model dedicated to 78 rpm records, whose round stylus has a large curvature radius at the tip. The curvature radius is 3 mil, and suitable for playing 78 rpm records from a wide variety of eras.Specifications:Frequency Response: 20-20,000 HzVertical Tracking Force: 4.5-5.5 g (5.0 g standard)Stylus Construction: Bonded round shankRecommended Load Impedance: 47,000 ohmsOutput: 3.0 mV (at 1 kHz, 5 cm/sec)Stylus Shape: 3.0 mil conicalMount: Half-inchReplacement Stylus: VMN70SP

The Audio-Technica AT81CP is a Dual Magnet phono cartridge with a P-mount (T4P) connector and a 0.6 mil conical stylus. It is the affordable way to bring a turntable with a P-mount tonearm back to life, such as many linear-tracking turntables from Technics, Pioneer and others.Stable, reliable trackingThe conical stylus with a carbon fibre reinforced ABS cantilever tracks records with stability and a warm, full sound, with 3.5 mV output and a 20 – 20,000 Hz response.Installation without adjustmentThe P-mount cartridge plugs straight into the tonearm and is secured with a single screw, with no geometry or tracking force adjustment. With the AT-PMA1 adapter it can also be fitted to a 1/2-inch headshell.

The cartridge of the Planar 1 and Planar 2The Rega Carbon is a high-quality moving magnet (MM) cartridge designed for easy fitting and setup, with accurate music reproduction as its main goal. It is the cartridge factory-fitted to the Planar 1 and Planar 2 turntables and Rega's most affordable MM cartridge. The company presents it as one of the best-performing cartridges in its class relative to its price.Standard mounting for any tonearmThe Carbon uses the established half-inch, two-screw mounting, so it can be fitted not only to Rega tonearms but also to arms from other manufacturers. Its wide tracking force range, from 2 to 3 g, makes it forgiving to set up and ideal for anyone taking their first steps into vinyl. An output of 2.5 mV at 1 kHz suits any MM phono stage.WarrantyIt is covered by Rega's Lifetime Limited Warranty against confirmed manufacturing defects. The stylus, as a consumable part, is easily replaced by the user.

The Ortofon Quintet moving coil cartridge system for high performance sound reproduction of your favourite analogue records! Ortofon has been working with sound reproduction since 1918. Ortofon developed its first phono cartridge in 1948, since then more than 300 different phono cartridges have been engineered and manufactured. Reflecting our extensive experience in industrial design and technological knowhow we have become the global leader in the manufacture and supply of phono cartridges.The Quintet Series has been engineered in accordance with the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration. Each of the five Quintet Series cartridges has its individual sonic expression, and all five models together represent the ensemble of five classic variations:Specifications:Output voltage at 1 kHz 5 cm/sec : 0,45 mVChannel balance : < 1,5 dBChannel separation at 1 kHz : > 23 dBChannel separation at 15 kHz : > 15 dBFrequency range at -3 dB : 20 Hz - 50 kHzFrequency response 20 Hz - 20 kHz : +3/-1Tracking ability at 315 Hz at recommended tracking force : 80 μmCompliance, dynamic, lateral : 12 μm/mNStylus type : Nude Fine Line on Alu cantileverStylus tip radius : r/R 8/40Tracking force range : 2,2-2,7 g (22-27 mN)Tracking force recommended : 2,5 g (25 mN)Tracking angle : 20ºInternal impedance, DC resistance : 5 OhmRecommended load impedance : 50-500 OhmCartridge body material : Stainless steel AluminiumCartridge colour : Red/Black Cartridge weight : 10,7 g