ATC SCM25A Pro mk II (Pair)

ATC SCM20A Pro MkII (Pair)

The ATC SCM20A Pro MkII (SCM20ASL Pro) are compact active 2-way studio monitors for critical near-field monitoring in any control room, as well as LCR or surround duty in small to large rooms. They combine ATC drive units, hand-built in England, with 250 W of built-in amplification per speaker.6.5″ Super Linear wooferThe 150 mm SB75-150SL woofer uses a 75 mm voice coil and a short-coil, long-gap topology, combining the power handling of large systems with the resolution of near-field monitors. ATC Super Linear technology uses specialist materials in the magnetic circuit to reduce third-harmonic distortion in the lower midrange.Dual-suspension tweeterThe 25 mm SH25-76S tweeter is designed and built by ATC. Its dual suspension removes the need for ferrofluid, so performance stays consistent over the years, and the machined alloy waveguide gives even ±80° horizontal dispersion.MOSFET class A/B amplificationThe built-in MOSFET class A/B bi-amp pack delivers 200 W to the woofer and 50 W to the tweeter. The balanced XLR input has a -12 dB sensitivity trim, and ATC protection momentarily reduces gain on overload, shown by a front-panel indicator.

6.550 €

ATC SCM45A Pro (Pair)

The ATC SCM45A Pro are mid-size active 3-way monitors in a horizontal cabinet. They are designed for critical near-field monitoring in any control room, LCR monitoring in medium rooms and surround channels in medium to large rooms.Twin 6.5″ woofersBass comes from two hand-built 164 mm short-coil woofers with carbon-paper cones. Response extends to 42 Hz (-6 dB) with up to 112 dB continuous SPL, from a cabinet that fits on the console.75 mm midrange dome and «S-Spec» tweeterThe ATC 75 mm soft-dome midrange sits at the centre of the cabinet with the 25 mm dual-suspension «S-Spec» tweeter. The symmetrical layout gives consistent ±80° horizontal dispersion and a clear centre image.MOSFET class A/B tri-ampThe built-in amplifier delivers 150 W to the bass, 60 W to the mid and 25 W to the high section. 4th-order filters at 380 Hz and 3.5 kHz include phase compensation. Rear-panel controls adjust input sensitivity (0 to -6 dB) and bass boost (0 to +3 dB at 40 Hz).

13.100 €

ATC SCM50ASL Pro (Pair)

The ATC SCM50ASL Pro are active 3-way monitors for reference monitoring in medium-sized rooms, as near-field or mid-field monitors. They combine a 9″ Super Linear woofer, the ATC 75 mm midrange dome and a dual-suspension tweeter with a built-in 350 W tri-amp pack.9″ Super Linear wooferThe 234 mm woofer is built to ATC full SL specification for low distortion and high power handling. Bass extends to 38 Hz (-6 dB) and maximum continuous SPL reaches 112 dB.75 mm «Super Dome» midrangeThe 75 mm SM75-150S soft-dome midrange is one of the defining ATC drive units. It covers the vocal and instrumental range from 380 Hz to 3.5 kHz with clarity and low distortion.350 W tri-amp with bass controlThe built-in amplifier delivers 200 W to the woofer, 100 W to the midrange and 50 W to the tweeter. A rear-panel LF EQ adds up to +6 dB at 40 Hz and input sensitivity is adjustable from 0 to -6 dB. Protection momentarily reduces gain on overload, with a front-panel warning. 6-year warranty.

17.900 €

Barefoot MicroMain27 Gen2 (Pair)

The MicroMain27 Gen2 is a 3.5-way active system with 5 drive units housed in sealed enclosures spanning 30Hz to 45kHz with vanishingly low distortion, breathtaking dynamic range and ultra-fast transient response. The ring radiator tweeter is incredibly detailed and produces very wide dispersion out to its highest frequencies. The new 5.25″ midbass features a phalanx of advanced technology, yielding midrange detail that rivals any driver on the planet. Barefoot has teamed up with the brilliant Bruno Putzeys of Hypex to develop the powerful and completely transparent amplifier stage of the MM27 Gen2. Melding the system together is a groundbreaking new DSP crossover that has taken Thomas Barefoot more than 4 years to develop. With beautifully designed high end converts and cutting edge proprietary filtering techniques the MM27 Gen2 sound stage is seamlessly coherent and deeply revealing. MEME™ Technology: Despite the advantages of high resolution monitors, Thomas Barefoot realizes that many engineers still use their NS10M’s † and mix cubes as secondary references. These speakers have long traditions and people find them familiar and useful for focusing in on certain aspects of their mix. However, crowding one’s console with those extra boxes degrades the sound field of the primary reference monitors. Not to mention, they are no longer manufactured, they need amplifiers, cable runs, and they consume more studio space. The solution is to make the MM27 sound and translate like those speakers. With the turn of a knob one can switch from the MicroMain27′s brutally revealing “Flat” response to the warmer and sweeter “Hi-Fi” setting, generically emulating the sound of some high end consumer audio gear. More specifically the “Old School” setting closely emulates the sound of the NS10M nearfield, while the “Cube” setting emulates the mid-centric sound of classic mix cubes The idea is not to perfectly replicate every subtle quirk of these venerable old speakers. That would be impossible. But the MM27 Gen2 can capture the essence of how they behave and translate, modeling their frequency, phase and transient responses, dynamic compression and even specific distortion components. If you know how to work on these speakers you will feel very comfortable working on the new MM27′s emulation settings.  MicroMain27 Gen2 features: 3.5-way active studio monitor with integral subwoofers Four-setting DSP voice emulation Analog and AES3 digital inputs Hypex amplification Tweeter - 1" ring radiator with Advanced neodymium motor Rear waveguide chamber. Amplifier: 250W Hypex Midbass 1 - 5.25" poly/paper cone with Advanced neodymium motor , with +/- 5 mm linear excursion. Amplifier: 250W Hypex Midbass 2 - 5.25" poly/paper cone with Advanced neodymium motor, with +/- 5 mm linear excursion. Amplifier: 250W Hypex Subwoofers - 2 x 10" aluminum cone with high linearity motor, with +/- 13 mm linear excursion. Amplifier: 500W Hypex Crossover Frequencies: 100 / 600 / 3000 Hz Cabinet Dimensions: 20.5" x 9.5" x 15.5" Overall Dimensions: 20.5" x 10.4" x. 17.4"

12.500 €

Barefoot Microstack 45 (Pair)

Barefoot’s compact MicroStack45 stereo system comprises two MicroMain45 3-way active nearfield reference monitors and two MicroSub45 Dual-Force™ technology subwoofers. Each system combines six high-excursion 8-inch woofers, four 2.5-inch midrange drivers and two 1-inch tweeters working seamlessly together as a single unit driven by 2220W of power.The MicroMain45 distills the resolution and accuracy of the MiniMain12 into a compact, lighter and more cost-conscious package shares the same amplifier, driver technology and DSP as Barefoot’s flagship system. The MicroMain45’s no-compromise design combines an 8-inch aluminum woofer, two 2.5-inch aluminum midrange drivers and a 1-inch tweeter to deliver over 600W of power with a 40 Hz–45 kHz frequency response.The MicroSub45 houses a pair of opposing 8-inch Dual-Force™ technology woofers and an analog high-pass filter crossing over from the MicroMain45 at 80 Hz, delivering clean low-frequency extension down to 25 Hz. Dual-Force, a core technology that is found in almost every Barefoot product, eliminates vibration within the MicroSub45 speaker cabinet through its innovative force cancellation design. The opposing woofers significantly reduce distortion and coloration, add a massive internal metal cabinet brace and cause the subs to radiate as if they were a single point source located on axis with the tweeter.A sturdy, non-slip tilt feature directs the MicroMain45 monitors at the listening sweet spot.Current MicroMain45 owners can add a pair of MicroSub45 Dual-Force technology subwoofers to create a MicroStack45 system.

13.518 ,03 €

PMC 6-2

The PMC6-2 provides main-monitor scale, depth, and dynamics, and allows mix decisions to be made quickly, with absolute certainty and without fatigue.This 3-way active monitor speaker combines two custom 6-inch ultra-long-throw bass-drivers with our radically engineered PMC55 2-inch soft-dome mid-range unit and a precision-built one-inch soft-dome tweeter. The PMC55’s distinctive ‘N-compass’ waveguide enhances the wide dispersion and remarkable mid-range projection of the driver; in combination with the high performance of the tweeter, the result is an ultra-wide and stable image, with a smooth and natural in-room response. Each bass driver is individually powered by a cutting-edge 400W Class-D amplifier and seamlessly integrated by our sophisticated, highly accurate DSP-based crossovers. As with the PMC6, the monitor is configured using rear-panel controls or the browser-based SoundAlign™ software, with comprehensive boundary and EQ options.

12.240 €

Adam S5V

Designed for medium-sized and larger studio control rooms, the S5V main monitor offers all the raw power studio professionals would expect from a reference speaker of its class, but also reproduces full-bandwidth, high-resolution audio with complete accuracy and clarity. ADAM Audio’s Extended Linear Excursion (ELE) bass drivers and Symmetrical Magnet Assembly (SMA) technology were developed especially for the S Series, and the 12-inch bass driver on the S5V benefits from both concepts, offering a quality of reproduction without equal in terms of accuracy, dynamic range and freedom from coloration. The 4-inch DCH MF driver, with its unique hybrid dome/cone construction, handles the important mid-range information with extreme precision, while ADAM Audio’s S-ART folded-ribbon tweeter, handmade in Berlin to the tightest possible tolerances, produces breathtaking highs and ensures the soundfield is presented in all of its most delicate, filigree detail. The off-axis responses of the treble and mid drivers remain extremely accurate thanks to the addition of high- and mid-frequency waveguides milled from solid aluminum: ADAM Audio’s newly developed Mid-range and High-frequency Propagation Systems (MPS and HPS). The resultant stable, wide-ranging dispersion ensures that teams of more than one person can work in the loudspeakers’ sweet spot simultaneously, as is often necessary in larger control rooms. The S Series’ custom-designed DSP optimizes the loudspeaker crossovers to create linear responses for the entire range, as well as providing user equalization and in-room tuning/voicing functions. The DSP also handles the limiter-based high-frequency driver protection, processes the signals from the AES3 digital inputs, and will in time facilitate various expansion options. Software updates can be carried out with ease via the associated USB port, which also allows users to connect computers and control the speakers’ DSP functions via a software front-end. A Class D 700 W amplifier drives the S5V’s bass unit, with further Class D designs providing 300 W and 100 W to the DCH mid and S-ART treble drivers respectively. Combining the legendary precision of ADAM Audio’s proprietary drivers with the power of the company’s amplification, the S5V is a reference monitor for truly discerning audio professionals at work in the most expansive listening environments.

9.509 €

Genelec 8351 B

The upgraded 8351B now offers increased SPL, additional room compensation EQs, equalised delay and enhanced HF response. Offering the same extraordinary imaging and uncoloured precision of its smaller 8331A and 8341A siblings, the 8351B provides even greater LF extension, while its higher maximum SPL enables longer listening distances.

4.033 €