go to top icon

Retro Instruments

Όλα τα προϊόντα Retro Instruments

2  Προϊόντα

O Retro Sta-Level είναι μια replica του θρυλικού 1956 Gates Sta-Level κομπρέσορα, ο οποίος κυριάρχισε στον ήχο της δεκαετίας του 60.Αναλυτικά: Gain Reduction Threshold: Continuously adjustable from +24dBm to -20dBm Available Gain Reduction: 40dB Total System Gain: 35dB (with standard input and output pads) Distortion: 1 percent or less from 0-30 dB gain reduction Frequency Response: ± .25dB from 20-20,000 Hz Noise: -70dB or better referenced to gain reduction threshold Output Level: Continuously adjustable from -40 dBm to +18 dBm Input Impedance: Accepts low impedance active or transformer balanced 0-600 Ohms Output Impedance: 600 Ohm transformer balanced, terminated and resistive pad coupled Tube Complement: 2-6BJ6), 1-12AT7, 2-6V6GT, 1-6AL5, 1-OB2, 1-5Y3 Power Requirements: Three prong IEC - Switchable 115-230 VAC - 50/60 Hz Mounting Requirements: 3U metal rack 5.25" high, 19" wide, 8" deep

3.154 €
36 Δόσεις 108,89€ / μήνα
Κατόπιν Παραγγελίας

Τα vintage λαμπάτα ενισχυτικά κυκλώματα και οι custom σχεδιασμένοι μετασχηματιστές είναι συστατικά για την “μεγάλη εικόνα” και το παθητικό equalization δημιουργεί όμορφες και μουσικές καμπύλες ισοστάθμισης.Το RETRO 2A3 είναι ένα δυκάναλο equalizer βασισμένο στο -industry standard-Pultec.Τα ηχιτικά του πλεονεκτήματα φτάνουν πέρα από το equalizing. Industry-standard Passive EQ with authentic feel, controls and equalization curves Additional HF Boost Frequencies for more precise control Easily recallable 100-position knob scales on boost and cut controls A ganged interstage-coupled Subsonic High-Pass Filter provides Peaking LF Boosts with alternate tonal characteristics Transformer Balanced and fully-floating 600 Ohm Input and Output to eliminate ground-induced hum and noise LF Boost Settings of 20, 30, 60 and 100 Hz Complementary LF Cut settings of 20, 30, 60 and 100 Hz HF Boost Settings of 1.5 kHz, 3 kHz, 4 kHz, 5 kHz, 6 kHz, 8 kHz, 10 kHz, 12 kHz, 14 kHz and 16 kHz Complementary HF Cut Settings of 5 kHz, 10 kHz and 20 kHz Vintage Class AB tube amplification for unity-gain make-up Equalization Bypass Switches Size 2U Height: 19" wide x 3.5" tall x 9" deep XLR input and output connections IEC power connector 115/230V 50-60 Hz Switchable AC Mains Uses readily available 12AX7(2) and 12AU7(2) electron tubes Tube substitutions are possible with internal unity gain calibration and jumper selectable 6 or 12 volt tube configuration Design minimizes tube heat generation High stability components used throughout Steel Chassis built to last Manufactured in the USA Full factory support Specifications Signal to noise ratio of greater than 76dB Channel Separation greater than 70 dB Frequency response is flat within 1 dB from 20 Hz-20,000 Hz Harmonic Distortion is less than 1% from 20 Hz-20,000 Hz

3.950 €
36 Δόσεις 136,37€ / μήνα
Κατόπιν Παραγγελίας